ISL6401 Intersil Corporation, ISL6401 Datasheet - Page 5

• Manufacturer Part Number: ISL6401
• Description: Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs)
• Manufacturer: Intersil Corporation

Typical Performance Curves
Pin Descriptions
SD - This pin is logic level compatible and can be pulled
high, tied to V
on the SD activates shutdown, reducing the part’s supply
current to approximately 55µA.
SYNC - This pin is the input pin for external frequency
synchronization. The switching frequency of the device can
be synchronized by an external clock signal inserted at this
pin. The oscillator timing capacitor, C
if an external clock is used. Program the free-running
frequency to be a minimum of 10% slower than the SYNC
input frequency.
CT - This is the oscillator timing pin. The free-running
frequency can be set by connecting a timing capacitor to this
pin. The oscillator produces a sawtooth waveform with a
programmable frequency range of 100kHz to 1.2MHz.
Figure 4 may be used as a guideline in selecting the
capacitor value required for a given frequency.
COMP - COMP is the output of the error amplifier and input
of the current comparator.
The ISL6401 features built-in full cycle soft start. Soft start is
implemented as a clamp on the maximum COMP voltage.
FB - Feedback pin that is used for positive output voltage
sensing. It is the inverting input of the error amplifier. The
non-inverting input of the error amplifier is internally tied to a
reference voltage.
NFB-IN - Negative feedback pin that is used for negative
output voltage sensing. It is connected to the inverting input
of the negative feedback amplifier through a 100K source
resistor.
NFB OUT - This pin is the output of the negative feedback
inverter. This pin should be connected the FB pin with a 10k
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
FIGURE 3. SUPPLY CURRENT vs TEMPERATURE
-40
IN
or left open for normal operation. Logic low
-20
TEMPERATURE (
5
25
T
, is still required, even
o
C)
(Continued)
60
85
ISL6401
series resistor for negative output voltage regulation
applications.
CS - This is the input of the current sense comparator. The
IC has two different comparators: The PWM comparator and
an overcurrent comparator.
The over current comparator is only intended for fault
sensing, and exceeding the over-current threshold will cause
a soft start cycle.
GND - GND is a small signal reference ground for all analog
functions on this part.
PGND - This pin provides a dedicated ground for the output
gate driver. The GND and PGND pins should be connected
externally using a short printed circuit board trace close to
the IC. This is imperative to prevent large, high frequency
switching currents flowing through the ground metallization
inside the IC. (Decouple PV
0.1µF capacitor.)
GATE - This is the device output. It is a high current power
driver capable of driving the gate of a power MOSFET with
peak currents exceeding 1.0A. This GATE output is actively
held low when V
The high-current power driver consists of FET output
devices, which can switch all the way to GND and all the way
to V
to overshoot and undershoot.
PV
gate drive. Separate PV
IC’s analog circuitry from the high power gate drive noise.
Connect this pin to V
circuit board.
V
quiescent V
CC
CC
CC
- V
600
500
400
300
200
100
- This pin is for separate collector supply to the output
. The output stage also provides very low impedance
0
CC
82
FIGURE 4. CAPACITANCE vs FREQUENCY
is the power connection for the device. Although
CC
120
current is very low, total supply current will be
CC
180
is below the UVLO threshold (3.7V typ).
CC
CC
with external short trace on printed
250
CAPACITANCE (pF)
and PGnd helps decouple the
CC
300
to PGND with a low ESR
390
510
610
820
1200