ISL9217 Intersil Corporation, ISL9217 Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
ISL9217
Manufacturer Part Number
ISL9217
Description
(ISL9216 / ISL9217) 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set
Manufacturer
Intersil Corporation
Datasheet
1.ISL9217.pdf
(33 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL9217IRZ
Manufacturer:
INTERSIL
Quantity:
101
Part Number:
ISL9217IRZ
Manufacturer:
INTERSIL
Quantity:
20 000
www.DataSheet4U.com
Pin Descriptions
VC7/VCC Battery Cell 7 Voltage Input/VCC Supply. This pin is used to monitor the voltage of this battery cell externally at pin AO. This pin also
SYMBOL
DSENSE Discharge Current Sense Monitor (ISL9216 only). This input monitors the discharge current by monitoring a voltage. It can monitor
CSENSE Charge Current Sense Monitor (ISL9216 only). This input monitors the charge current by monitoring a voltage. It can monitor the
VCELLN Battery Cell N Voltage Input. This pin is used to monitor the voltage of this battery cell externally at pin AO. VCELLN connects to the
TEMP3V Temperature Monitor Output Control (ISL9216 only). This pin outputs a voltage to be used in a divider that consists of a fixed resistor
DSREF
VMON
TEMPI
WKUP
DFET
CFET
RGO
RGC
CBN
VSS
AO
provides the operating voltage for the IC circuitry.
positive terminal of CELLN and the negative terminal of CELLN+1.
Cell Balancing FET Control Output N. This internal FET diverts a fraction of the current around a cell while the cell is being charged
or adds to the current pulled from a cell during discharge in order to perform a cell voltage balancing operation. This function is generally
used to reduce the voltage on an individual cell relative to other cells in the pack. The cell balancing FETs are turned on or off by an
external controller.
Ground. This pin connects to the most negative terminal in the battery string.
Discharge Current Sense Reference (ISL9216 only). This input provides a separate reference point for the charge and discharge
current monitoring circuits. with a separate reference connection, it is possible to minimize errors that result from voltage drops on the
ground lead when the load is drawing large currents. If a separate reference is not necessary, connect this pin to VSS.
the voltage across a sense resistor, or the voltage across the DFET, or by using a FET with a current sense pin. The voltage on this
pin is measured with reference to DSREF.
voltage across a sense resistor, or the voltage across the CFET, or by using a FET with a current sense pin. The voltage on this pin is
measured with reference to VSS.
Discharge FET Control (ISL9216 only). The ISL9216 controls the gate of a discharge FET through this pin. The power FET is a N-
Channel device. The FET is turned on only by the microcontroller. The FET can be turned off by the microcontroller, but the ISL9216
can also turn off the FET in the event of an overcurrent or short circuit condition. If the microcontroller detects an undervoltage condition
on any of the battery cells, it will turn off the FET off by controlling this output with a control bit.
Charge FET Control (ISL9216 only). The ISL9216 controls the gate of a charge FET through this pin. The power FET is a N-Channel
device. The FET is turned on only by the microcontroller. The FET can be turned off by the microcontroller, but the ISL9216 can also
turn off the FET in the event of an overcurrent condition. If the microcontroller detects an overvoltage condition on any of the battery
cells, it will turn off the FET off by controlling this output with a control bit.
Discharge Load Monitoring (ISL9216 only). In the event of an overcurrent or short circuit condition, the microcontroller can enable
a series diode and resistor that connects between the VMON pin and VSS. When FETs open because of an overcurrent or short circuit
condition, and the load remains, the voltage at VMON will be near the VCC voltage. When the load is released, the voltage at VMON
drops below a threshold indicating that the overcurrent or short circuit condition is resolved. At this point, the LDFAIL flag is cleared
and operation can resume.
Analog Multiplexer Output. The analog output pin is used by an external microcontroller to monitor the cell voltages and temperature
sensor voltages. The microcontroller selects the specific voltage being applied to the output by writing to a control register.
and a thermistor. The thermistor is located in close proximity to the cells. The TEMP3V output is connected internally to the RGO
voltage through a PMOS switch only during a measurement of the temperature, otherwise the output is off. The TEMP3V output can
be turned on continuously with a special control bit.
Microcontroller Wake-up Control. This pin is also turned on when any of the DSC, DOC, or COC bits are set. This can be used to
wake-up a sleeping microcontroller to respond to overcurrent conditions with its own control mechanism.
Temperature Monitor Input (ISL9216 only). This pin inputs the voltage across a thermistor to determine the temperature of the cells.
When this input voltage drops below TEMP3V/13, an external over-temperature condition exists. The TEMPI voltage is also fed to the
AO output pin through an analog multiplexer so the temperature of the cells can be monitored by the microcontroller.
Regulated Output Voltage. This pin connects to the emitter of an external NPN transistor and works in conjunction with the RGC pin
to provide a regulated 3.3V. The voltage at this pin provides feedback for the regulator and power for many of the ISL9216 and ISL9217
internal circuits. For the ISL9216, this output also provides the 3.3V output voltage for the microcontroller and other external circuits.
Regulated Output Control. This pin connects to the base of an external NPN transistor and works in conjunction with the RGO pin to
provide a regulated 3.3V. The RGC output provides the control signal to provide the 3.3V regulated voltage on the RGO pin.
Wake-up Voltage. This input wakes up the part when the voltage crosses a turn-on threshold (wake-up is edge triggered) and the
condition of the pin is reflected in the WKUP bit (The WKUP bit is level sensitive).
• WKPOL bit = ”1”: the device wakes up on the rising edge of the WKUP pin. Also, the WKUP bit is HIGH only when the WKUP pin
• WKPOL bit = ”0”, the device wakes up on the falling edge of the WKUP pin. Also, the WKUP bit is HIGH only when the WKUP pin
voltage > threshold.
voltage < threshold.
4
ISL9216, ISL9217
DESCRIPTION
November 2, 2007
FN6488.1