BUL147 Motorola Inc, BUL147 Datasheet
BUL147
Available stocks
Related parts for BUL147
BUL147 Summary of contents
Page 1
... No Coil Required in Base Circuit for Turn–Off (No Current Tail) Parametric Distributions are Tight and Consistent Lot–to–Lot Two Package Choices: Standard TO–220 or Isolated TO–220 BUL147F, Isolated Case 221D Recognized to 3500 V RMS : File #E69369 MAXIMUM RATINGS Rating Collector–Emitter Sustaining Voltage Collector– ...
Page 2
... BUL147 BUL147F ELECTRICAL CHARACTERISTICS — continued Characteristic ON CHARACTERISTICS Base–Emitter Saturation Voltage ( 2.0 Adc 0.2 Adc) Base–Emitter Saturation Voltage ( 4.5 Adc 0.9 Adc) Collector–Emitter Saturation Voltage ( 2.0 Adc 0.2 Adc 4.5 Adc 0.9 Adc) DC Current Gain ( 1.0 Adc 5.0 Vdc) DC Current Gain ( ...
Page 3
... Figure 4. Collector–Emitter Saturation Voltage 10000 C ib 1000 C ob 100 COLLECTOR–EMITTER VOLTAGE (VOLTS) BUL147 BUL147F 0 COLLECTOR CURRENT (AMPS 125 C 0 COLLECTOR CURRENT (AMPS MHz ...
Page 4
... BUL147 BUL147F TYPICAL SWITCHING CHARACTERISTICS 600 I B(off 300 500 400 125 C 300 200 100 COLLECTOR CURRENT (AMPS) Figure 7. Resistive Switching 3500 3000 2500 2000 ...
Page 5
... The safe level is specified as a reverse–biased safe operating area (Figure 16). This rating is verified under clamped conditions so that the device is never subjected to an avalanche mode. BUL147 BUL147F I B(off 300 V ...
Page 6
... BUL147 BUL147F dyn dyn –1 90 – –3 – – TIME Figure 18. Dynamic Saturation Voltage Measurements + 100 150 MPF930 MPF930 + COMMON 150 3 W 500 F –V off Table 1. Inductive Load Switching Drive Circuit 3– ...
Page 7
... D = 0.5 0.2 0.1 0.1 0.05 0.02 SINGLE PULSE 0.01 0.01 0.1 Figure 20. Typical Thermal Response (Z JC (t)) for BUL147 0.5 0.2 0.1 0.1 0.05 0.02 SINGLE PULSE 0.01 0.01 0.1 Figure 21. Typical Thermal Response (Z JC (t)) for BUL147F Motorola Bipolar Power Transistor Device Data TYPICAL THERMAL RESPONSE P (pk DUTY CYCLE TIME (ms) P (pk) ...
Page 8
... BUL147 BUL147F TEST CONDITIONS FOR ISOLATION TESTS* MOUNTED FULLY ISOLATED CLIP PACKAGE LEADS HEATSINK 0.110 MIN Figure 22a. Screw or Clip Mounting Position for Isolation Test Number 1 * Measurement made between leads and heatsink with all leads shorted together. 4–40 SCREW PLAIN WASHER ...
Page 9
... COLLECTOR 3. EMITTER BUL44F CASE 221D–02 (ISOLATED TO–220 TYPE) ISSUE D BUL147 BUL147F NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. INCHES MILLIMETERS DIM MIN ...
Page 10
... BUL147 BUL147F Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “ ...