SY10E016JY Micrel Inc, SY10E016JY Datasheet - Page 8

• Manufacturer Part Number: SY10E016JY
• Description: IC UPCOUNTER 8BIT SYNC 28-PLCC
• Manufacturer: Micrel Inc
• Series: 10Er

Specifications of SY10E016JY

• Logic Type: Binary Counter
• Direction: Up
• Number Of Elements: 1
• Number Of Bits Per Element: 8
• Reset: Asynchronous
• Timing: Synchronous
• Count Rate: 900MHz
• Trigger Type: Positive Edge
• Voltage - Supply: 4.2 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-LCC (J-Lead)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 576-2482; SY10E016JY

Micrel, Inc.
is used as the divide output and the pulse duration is equal to
a full clock period. For even divide ratios twice the desired
divide ratio can be loaded into the E016 and the TC output can
feed the clock input of a toggle flip-flop to create a signal
divided as desired with a 50% duty cycle.
256, inclusive. If divide ratios of greater than 256 are needed,
multiple E016s can be cascaded in a manner similar to that
already discussed. When E016s are cascaded to build larger
dividers, the TCLD pin will no longer provide a means for
loading on terminal count. Because one does not want to
reload the counters until all of the devices in the chain have
reached terminal count, external gating of the TC pins must be
used for multiple E016 divider chains.
diagram of a 32-bit divider chain. Once again, the maximize
the frequency of operation, E101 OR gates were used. For
lower frequency applications, a slower OR gate could replace
the E101. Note that for a 16-bit divider, the OR function
feeding the PE (program enable) input CANNOT be replaced
by a wire OR tie as the TC output of the least significant E016
must also feed the CE input of the most significant E016. If the
M9999-032006
[e-mail] or [phone]
A single E016 can be used to divide by any ratio from 2 to
Figure 4 on the following page shows a typical block
Divide
Ratio
112
113
114
254
255
256
2
3
4
5
•
•
•
•
P
H
H
H
H
H
H
H
L
L
L
•
•
•
•
7
P
H
H
H
H
L
L
L
L
L
L
•
•
•
•
6
Table 1. Preset Values for Various Divide Ratios
P
H
H
H
H
L
L
L
L
L
L
•
•
•
•
5
Preset Data Inputs
P
H
H
H
H
H
8
L
L
L
L
L
•
•
•
•
4
two TC outputs were OR tied, the cascaded count operation
would not operate properly. Because in the cascaded form
the PE feedback is external and requires external gating, the
maximum frequency of operation will be significantly less than
the same operation in a single device.
Maximizing E016 Count Frequency
ended outputs; thus, V
situations where all of the outputs switch simultaneously in the
same direction. This V
maximum frequency of operation of the device. Since the
device does not need to have the Q outputs terminated to
count properly, it is recommended that, if the outputs are not
going to be used in the rest of the system, they should be left
unterminated. In addition, if only a subset of the Q outputs are
used in the system, only those outputs should be terminated.
Not terminating the unused outputs will not only cut down the
V
dissipation. Following these guidelines will allow designers to
either be more aggressive in their designs, or provide them
CC
The E016 device produces nine fast transitioning single-
noise generated, but will also save in total system power
P
H
H
H
H
H
H
L
L
L
L
•
•
•
•
3
CC
CC
P
H
H
H
H
H
L
L
L
L
L
•
•
•
•
2
noise can become significant in
noise can negatively impact the
P
H
H
H
H
H
L
L
L
L
L
•
•
•
•
1
SY100E016
SY10E016
P
H
H
H
H
L
L
L
L
L
L
•
•
•
•
0