SA8281 Mitel Networks Corporation, SA8281 Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
SA8281
Manufacturer Part Number
SA8281
Description
Three-Phase PWM Waveform Generator
Manufacturer
Mitel Networks Corporation
Datasheet
1.SA8281.pdf
(14 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SA8281B
Manufacturer:
MITEL
Quantity:
20 000
Part Number:
SA8281BIG
Manufacturer:
MITEL
Quantity:
20 000
Company:
Part Number:
SA8281IG
Manufacturer:
UC
Quantity:
6 224
Part Number:
SA8281IG
Manufacturer:
MITEL
Quantity:
20 000
Part Number:
SA8281SLABA
Manufacturer:
MITEL
Quantity:
20 000
Output Trip Status (TRIP output)
and is active low.
Reset (RST input)
(low):
1. All PWM outputs are forced low (if not already low) thereby
turning off the drive switches.
2. All internal counters are reset to zero (this corresponds to 0
for the red phase output).
3. The rising edge of RST reactivates the PWM outputs
resetting the output trip and setting the TRIP output high –
assuming that the SET TRIP input is inactive (i.e. Iow).
the device into a factory test mode. This is achieved by writing
dummy data to R5 immediately after RST goes high. Care
must be exercised to ensure that the microprocessor/controller
cannot write to this register.
Zero Phase Pulses (ZPPR, ZPPY and ZPPB outputs)
frequency as the power frequency with a 1 : 2 mark-space
ratio. When in the forward mode of operation the falling edge
of ZPPR corresponds to 0 for the red phase, the falling edge
of ZPPY to 0 for the yellow phase and the ZPPB falling edge
to 0 for the blue phase. In the reverse mode, the rising edge
of a zero phase pulse corresponds to 0 for the relevant phase
PWM output.
Waveform Sampling Synchronisation (WSS output)
cycle at a frequency 1536 times higher than the fundamental
of the power waveform. Each successive pulse of WSS
corresponds to the SA828 reading the next location of the
waveform ROM. It may be used in conjunction with the ZPP
signals to monitor the position of the machine rotor and may
form part of a closed loop control system such as slip
compensation.
Clock (CLK input)
SA828 for all timings related to the PWM outputs. The
microprocessor interface, however, derives all its timings from
the microprocessor and therefore the microprocessor and the
SA828 may be run either from the same or from different
clocks.
HARDWARE INPUT/OUTPUT FUNCTIONS
Set Output Trip (SET TRIP input)
microprocessor interface in order to allow an external source
to override the microprocessor and provide a rapid shutdown
facility. For example, logic signals from overcurrent sensing
circuitry or the microprocessor ‘watchdog’ might be used to
activate this input.
trip latch is activated. This results in the TRIP output and the
six PWM outputs being latched low immediately. This condition
can only be cleared by applying a reset cycle to the RST input.
isolated from potential sources of noise; on no account should
it be left floating.
order to reduce noise sensitivity.
10
SA828
The TRIP output indicates the status of the output trip latch
The RST input performs the following functions when active
A sixth register, R5, located at A2:O = 101 is used to place
The zero phase pulse outputs provide pulses at the same
This output provides a square wave signal of 50% duty
The CLK input provides a timing reference used by the
The SET TRIP input is provided separately from the
When the SET TRIP input is taken to a logic high, the output
It is essential that when not in use SET TRIP is tied low and
SET TRIP is latched internally at the master clock rate in
WAVEFORM DEFINITION
output sequences is read from the internal 384X8 ROM. This
contains the 90 span of the waveform as shown in Fig. 18.
Each successive 8-bit sample linearly represents the
instantaneous amplitude of the waveform. It is assumed that
the waveform is symmetrical about the 90 , 180 and 270 axes.
The SA828 reconstructs the full 360 waveform by reading the
0 -90 section held in ROM and assigning negative values for
the second half of the cycle.
amplitudes for all three phases, which will be 120 transposed
in the normal R-Y-B orientation for forward rotation or B-Y-R for
reverse rotation. The 384 8-bit samples are regularly spaced
over the 0 to 90 span, giving an angular resolution of
approximately 0·23 .
PRODUCT DESIGNATION
are designated SA828-1 and SA828-2 as follows:
SA828-1
fundamental:
SA828-2
Additional wave shapes can be implemented to order, provided
they are symmetrical about the 90 , 180 and 270 axes.
Contact your local Mitel Semiconductor Customer Service
Centre for further details.
The waveform amplitude data used to construct the PWM
These samples are used to calculate the instantaneous
Two standard options exist, defining waveform shape. These
Sine + third harmonic at one-sixth the amplitude of the
Pure sinewave:
Table 8 90 of the 360 cycle is divided into 384 8-bit
Waveform segment
Fig. 18 90 sample of typical power waveform
SAMPLE
60·23 - 89·77
VALUE
8-BIT
30·23 - 60
OF
0 - 30
255
0
0
x(t) = A [ sin ( t ) + sin 3( t) ]
PHASE (384-BIT RESOLUTION)
x(t) = A [ sin ( t )]
samples
45
WAVEFORM
1
6
POWER
Sample number
128 - 255
256 - 383
0 - 127
90