TDF5140 Philips Semiconductors, TDF5140 Datasheet
![no-image](/images/manufacturer_photos/0/5/522/philips_semiconductors_sml.jpg)
TDF5140
Related parts for TDF5140
TDF5140 Summary of contents
Page 1
... TDF5140A Brushless DC motor drive circuit Product specification hilips Semiconductors INTEGRATED CIRCUITS 1999 March 15 ...
Page 2
... VCR Laser beam printer Fax machine Blower Automotive. GENERAL DESCRIPTION The TDF5140A is a bipolar integrated circuit used to drive 3-phase brushless DC motors in full-wave mode. The device is sensorless (saving of 3 hall-sensors) using the back-EMF sensing technique to sense the rotor position. CONDITIONS note 1 note 2 ...
Page 3
... COMMUTATION LOGIC TIMING DIVIDE BY 2 POSITION DETECTOR STAGE PGIN GND2 GND1 Fig.1 Block diagram 3 VMOT 4 PUSH/PULL FLYBACK D H OUTPUT D L DRIVER STAGE 1 OUTPUT DRIVER STAGE 2 OUTPUT DRIVER STAGE 3 EMF COMPARATORS Product specification TDF5140A 1 MOT1 3 MOT2 16 MOT3 17 MOT0 MGH313 ...
Page 4
... AMP OUT 15 transconductance amplifier output (open collector) MOT3 16 driver output 3 MOT0 17 input from the star point of the motor coils GND1 18 ground (0 V) motor supply return for output stages 1999 March 15 DESCRIPTION 4 Product specification TDF5140A ...
Page 5
... Brushless DC motor drive circuit FUNCTIONAL DESCRIPTION The TDF5140A offers a sensorless three phase motor drive function unique in its combination of sensorless motor drive and full-wave drive. The TDF5140A offers protected outputs capable of handling high currents and can be used with star or delta connected motors. It can easily be adapted for different motors and applications. The TDF5140A offers the following features: Sensorless commutation by using the motor EMF ...
Page 6
... Every pin withstands the ESD test in accordance with “MIL-STD-883C class 2” . Method 3015 (HBM 1500 , 100 pF) 3 pulses + and 3 pulses on each pin referenced to ground. 1999 March 15 MBD535 50 100 150 200 amb CONDITIONS see Fig. 3 see “Handling” 6 Product specification TDF5140A MIN. MAX GND VMOT DHF 2 ...
Page 7
... 100 100 6.8 VMOT 500 mA; notes and 5; see Fig 500 mA; notes 4 and see Fig.1 note 5 7 Product specification TDF5140A MIN. TYP. MAX 3 1 130 140 150 0 VMOT 10 0 ...
Page 8
... R = 330 ; 0 after pulse 5 1.5 2.5 0.05 V < V < 0.3 V CAP-TI 0.3 V < V < 2.2 V CAP-TI 8 Product specification TDF5140A TYP. MAX. UNIT mA 1.5 2 650 107 0 0 ...
Page 9
... Value selected for 3 Hz start-up oscillator frequency. Fig.4 Application diagram without use of the operational transconductance amplifier (OTA). 1999 March 15 CONDITIONS ; mA GND1 TDF5140A PGIN VMOT 10 F PG/FG 9 Product specification TDF5140A MIN. TYP. 10.6 16.2 22 5.3 8.1 1.85 2.05 2.25 850 875 900 2.3 2.4 2.55 10.1 15.5 20.9 20.9 15.5 0.9 1.025 1.15 850 875 900 2 ...
Page 10
... H Z control amplifier. The output is capable of directly driving external power transistor. The TDF5140A is designed for systems with low current consumption: use of I output transistors (patented), possibility of using a pick-up coil without bias current. 10 Product specification TDF5140A ...
Page 11
... ROTATION micro- SPEED/ DETECTOR processor 4.7 OUTPUT k STAGE GND2 TDF5140A GND1 Fig.5 Typical application of the TDF5140A as a scanner driver, with use of OTA. 1999 March BD434 1 F 470 47 nF 120 15 13 START-UP OSCILLATOR ADAPTIVE COMMUTATION DELAY COMMUTATION LOGIC ...
Page 12
... If the movement of the motor generates enough EMF the TDF5140A will run the motor. If the amount of EMF generated is insufficient, then the motor will move one step only and will oscillate in its new position. The amplitude of ...
Page 13
... CAP- recommended. To ensure a good start-up and commutation, care must be taken that no oscillations occur at the trailing edge of the flyback pulse. Snubber networks at the outputs should be critically damped. Typical voltage waveforms are illustrated by Fig.7. 13 Product specification TDF5140A ...
Page 14
... Possibilities of motor control Reliability. FG SIGNAL The FG signal is generated in the TDF5140A by using the zero-crossing of the motor EMF from the three motor windings. Every zero-crossing in a (star connected) motor winding is used to toggle the FG output signal. The FG frequency is therefore half the commutation frequency. ...
Page 15
... sensor is not used, the PG IN input must be grounded, this will result in a 50% duty factor FG signal. 1999 March 15 tolerance Fig.8 Timing and the FG and PG IN signals Product specification TDF5140A MGH319 2 GND2 MBD696 Fig.9 Pick-up coil as PG sensor. ...
Page 16
... It is possible, that when braking, the motor voltage (via the flyback diodes and the impedance on VMOT) may cause higher currents than allowed ( 0.6 A). These currents must be limited externally. 16 Product specification TDF5140A ...
Page 17
... Philips Semiconductors Brushless DC motor drive circuit PACKAGE OUTLINES 3.9 3.4 0.85 max 18 1 Dimensions in mm. 1999 March 15 22.00 21.35 2.54 0.53 (8x) max 1.4 max 10 9 Fig.10 18-pin dual in-line; plastic (SOT102). 17 Product specification TDF5140A 8.25 7.80 3.7 max 4.7 max 0.51 min 0.254 M 0.32 max 7.62 9.5 8.3 MSA259 6.48 6.14 ...
Page 18
... Apply the soldering iron below the seating plane (or not more than 2 mm above it). If its temperature is below 300 C, it must not be in contact for more than between 300 and 400 C, for not more than 5 s. 1999 March 15 18 Product specification TDF5140A ...
Page 19
... Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. hilips Semiconductors yyyy mmm dd Fax: + 24825 Document order number: 1 Product specification TDF5140A Koninklijke Philips Electronics N.V. 1999 All rights reserved. Printed in U.S.A. Date of release: 03-99 9397 750 08754 ...