AD9251BCPZRL7 Analog Devices, Inc., AD9251BCPZRL7 Datasheet - Page 28
![no-image](/images/no-image-200.jpg)
AD9251BCPZRL7
Manufacturer Part Number
AD9251BCPZRL7
Description
14-bit, 20 Msps/40 Msps/65 Msps/80 Msps, 1.8 V Dual Analog-to-digital Converter
Manufacturer
Analog Devices, Inc.
Datasheet
1.AD9251BCPZRL7.pdf
(36 pages)
AD9251
SERIAL PORT INTERFACE (SPI)
The AD9251 serial port interface (SPI) allows the user to configure
the converter for specific functions or operations through a
structured register space provided inside the ADC. The SPI
gives the user added flexibility and customization, depending
on the application. Addresses are accessed via the serial port
and can be written to or read from via the port. Memory is
organized into bytes that can be further divided into fields,
which are documented in the section for detailed operational
information, see AN-877 Application Note, Interfacing to High
Speed ADCs via SPI.
CONFIGURATION USING THE SPI
Three pins define the SPI of this ADC: the SCLK/DFS, the
SDIO/DCS, and the CS (see Table 13). The SCLK/DFS (a serial
clock) is used to synchronize the read and write data presented
from and to the ADC. The SDIO/DCS (serial data
input/output) is a dual-purpose pin that allows data to be sent
and read from the internal ADC memory map registers. The CS
(chip select bar) is an active-low control that enables or disables
the read and write cycles.
Table 13. Serial Port Interface Pins
Pin
SCLK
SDIO
CS
The falling edge of the CS, in conjunction with the rising edge
of the SCLK, determines the start of the framing. An example of
the serial timing and its definitions can be found in Figure 50
and Table 5.
Other modes involving the CS are available. The CS can be held
low indefinitely, which permanently enables the device; this is
called streaming. The CS can stall high between bytes to allow
for additional external timing. When CS is tied high, SPI
functions are placed in high impedance mode. This mode turns
on any SPI pin secondary functions.
During an instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase, and its length is determined
by the W0 and W1 bits.
All data is composed of 8-bit words. The first bit of the first byte in
a multibyte serial data transfer frame indicates whether a read
command or a write command is issued. This allows the serial
data input/output (SDIO) pin to change direction from an input
to an output.
Function
Serial Clock. The serial shift clock input, which is used to
synchronize serial interface reads and writes.
Serial Data Input/Output. A dual-purpose pin that
typically serves as an input or an output, depending on
the instruction being sent and the relative position in the
timing frame.
Chip Select Bar. An active-low control that gates the read
and write cycles.
Rev. PrH | Page 28 of 36
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used both to program the chip and to read
the contents of the on-chip memory. If the instruction is a readback
operation, performing a readback causes the serial data input/
output (SDIO) pin to change direction from an input to an output
at the appropriate point in the serial frame.
Data can be sent in MSB-first mode or in LSB-first mode. MSB
first is the default on power-up and can be changed via the SPI
port configuration register. For more information about this
and other features, see the AN-877 Application Note, Interfacing
to High Speed ADCs via SPI.
HARDWARE INTERFACE
The pins described in Table 13 comprise the physical interface
between the user programming device and the serial port of the
AD9251. The SCLK pin and the CS pin function as inputs when
using the SPI interface. The SDIO pin is bidirectional,
functioning as an input during write phases and as an output
during readback.
The SPI interface is flexible enough to be controlled by either
FPGAs or microcontrollers. One method for SPI configuration
is described in detail in the AN-812 Application Note,
Microcontroller-Based Serial Port Interface (SPI) Boot Circuit.
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK signal, the CS signal, and the SDIO signal are typically
asynchronous to the ADC clock, noise from these signals can
degrade converter performance. If the on-board SPI bus is used for
other devices, it may be necessary to provide buffers between
this bus and the AD9251 to prevent these signals from transi-
tioning at the converter inputs during critical sampling periods.
Some pins serve a dual function when the SPI interface is not
being used. When the pins are strapped to AVDD or ground
during device power-on, they are associated with a specific
function. The Digital Outputs section describes the strappable
functions supported on the AD9251.
Preliminary Technical Data