TS80C51RA2 Atmel Corporation, TS80C51RA2 Datasheet - Page 53

no-image

TS80C51RA2

Manufacturer Part Number
TS80C51RA2
Description
High Performance 8-bit Microcontroller
Manufacturer
Atmel Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TS80C51RA2-LCB
Manufacturer:
TEMIC
Quantity:
114
Part Number:
TS80C51RA2-LCB
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
TS80C51RA2-LCE
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
TS80C51RA2-LIB
Manufacturer:
TEMIC
Quantity:
5
Part Number:
TS80C51RA2-LIB
Quantity:
18
Part Number:
TS80C51RA2-LIB
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
TS80C51RA2-MCB
Manufacturer:
CY
Quantity:
1 590
Part Number:
TS80C51RA2-MCB
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
TS80C51RA2-MCE
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
TS80C51RA2-VCB
Manufacturer:
TEMIC
Quantity:
19
Programming Algorithm
Verify algorithm
4188A–8051–10/02
* See Table 31. for proper value on these inputs
PROGRAM SIGNALS*
CONTROL SIGNALS*
4 to 6 MHz
Figure 18. Set-Up Modes Configuration
The Improved Quick Pulse algorithm is based on the Quick Pulse algorithm and
decreases the number of pulses applied during byte programming from 25 to 1.
To program the TS87C51RB2/RC2/RD2 the following sequence must be exercised:
Repeat step 2 through 6 changing the address and data for the entire array or until the
end of the object file is reached (See Figure 19).
Code array verify must be done after each byte or block of bytes is programmed. In
either case, a complete verify of the programmed array will ensure reliable programming
of the TS87C51RB2/RC2/RD2.
P 2.7 is used to enable data output.
To verify the TS87C51RB2/RC2/RD2 code the following sequence must be exercised:
Repeat step 2 through 3 changing the address for the entire array verification (See Fig-
ure 19.)
The encryption array cannot be directly verified. Verification of the encryption array is
done by observing that the code array is well encrypted.
Step 1: Activate the combination of control signals.
Step 2: Input the valid address on the address lines.
Step 3: Input the appropriate data on the data lines.
Step 4: Raise EA/VPP from VCC to VPP (typical 12.75V).
Step 5: Pulse ALE/PROG once.
Step 6: Lower EA/VPP from VPP to VCC
Step 1: Activate the combination of program and control signals.
Step 2: Input the valid address on the address lines.
Step 3: Read data on the data lines.
PSEN
P2.6
P2.7
P3.3
P3.6
P3.7
XTAL1
EA/VPP
ALE/PROG
RST
P2.0-P2.5
P3.4-P3.5
P0.0-P0.7
P1.0-P1.7
VCC
VSS
GND
+5V
D0-D7
A0-A7
A8-A15
TS8xC51Rx2
53

Related parts for TS80C51RA2