LTC2900 Linear Technology, LTC2900 Datasheet - Page 11
LTC2900
Manufacturer Part Number
LTC2900
Description
Programmable Quad Supply Monitor with Adjustable Reset Timer
Manufacturer
Linear Technology
Datasheet
1.LTC2900.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC2900-1CDD
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC2900-1CDD#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC2900-1CDD#TRPBF
Manufacturer:
LT
Quantity:
658
Part Number:
LTC2900-1CDD#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC2900-1CMS
Manufacturer:
LT
Quantity:
5 321
Company:
Part Number:
LTC2900-1CMS
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC2900-1CMS
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC2900-1CMS#PBF
Manufacturer:
LINEAR
Quantity:
1
Part Number:
LTC2900-1CMS#TRPBF
Manufacturer:
LT/凌特
Quantity:
20 000
Part Number:
LTC2900-1CMS(LTYJ)
Manufacturer:
LT/凌特
Quantity:
20 000
APPLICATIO S I FOR ATIO
Although all four supply monitor comparators have built-
in glitch immunity, bypass capacitors on V1 and V2 are
recommended because the greater of V1 or V2 is also the
V
inputs are allowed.
Power-Down
On power-down, once any of the V
their threshold, RST is held at a logic low. A logic low of
0.4V is guaranteed until both V1 and V2 drop below 1V. If
the bandgap reference becomes invalid (V
part will reprogram once V
Monitor Output Rise and Fall Time Estimation
The RST output has strong pull-down capability. If the
external load capacitance (C
time (10% to 90%) is estimated using:
where R
transistor. The typical performance curve (V
demonstrates that the pull-down current is somewhat
linear versus output voltage. Using the 25 C curve, R
estimated to be approximately 40 . Assuming a 150pF
load capacitance, the fall time is about 13.2ns.
Although the RST output of the LTC2900-1 is considered
to be “open-drain,” it does have weak pull-up capability
(see RST Pull-Up Current vs V2 curve). Output rise time
(10% to 90%) is estimated using:
where R
The on-resistance as a function of the V2 voltage at room
temperature is estimated using:
CC
t
t
FALL
RISE
for the device. Filter capacitors on the V3 and V4
PD
PU
2.2 • R
2.2 • R
is the on-resistance of the internal pull-down
is the on-resistance of the pull-up transistor.
PD
PU
U
• C
• C
LOAD
LOAD
U
CC
LOAD
rises above 2.4V max.
) is known, output fall
W
X
inputs drop below
CC
< 2V typ), the
OL
U
vs I
SINK
PD
is
)
with V2 = 3.3V, R
capacitance, the rise time is 86 s. If the output needs to
pull up faster and/or to a higher voltage, a smaller
external pull-up resistor may be used. Using a 10k pull-
up resistor, the rise time is reduced to 3.3 s for a 150pF
load capacitance.
The LTC2900-2 has an active pull-up to V2 on the RST
output. The typical performance curve (RST Pull-Up Cur-
rent vs V2 curve) demonstrates that the pull-up current is
somewhat linear versus the V2 voltage and R
mated to be approximately 625 . A 150pF load capaci-
tance makes the rise time about 206ns.
Selecting the Reset Timing Capacitor
The reset time-out period is adjustable in order to accom-
modate a variety of microprocessor applications. The
reset time-out period, t
capacitor, C
of this capacitor is determined by:
with C
millisecond of delay can also be expressed as C
217 (pF/ms).
Leaving the CRT pin unconnected will generate a mini-
mum reset time-out of approximately 50 s. Maximum
reset time-out is limited by the largest available low
leakage capacitor. The accuracy of the time-out period will
be affected by capacitor leakage (the nominal charging
current is 2 A) and capacitor tolerance. A low leakage
ceramic capacitor is recommended.
C
R
RT
PU
RT
= t
in Farads and t
RST
6 10
V
RT
•
2 1
• 217 • 10
–
, between the CRT pin and ground. The value
5
PU
is about 260k. Using 150pF for load
RST
RST
–9
, is adjusted by connecting a
in seconds. The C
LTC2900
RT
PU
value per
RT
11
is esti-
/ms =
2900f