LTC4008 Linear Technology, LTC4008 Datasheet - Page 15

• Manufacturer Part Number: LTC4008
• Description: Multi-Chemistry Battery Charger
• Manufacturer: Linear Technology

www.DataSheet4U.com
APPLICATIO S I FOR ATIO
Selection criteria for the power MOSFETs include the “ON”
resistance R
transfer capacitance C
output current. The charger is operating in continuous
mode so the duty cycles for the top and bottom MOSFETs
are given by:
The MOSFET power dissipations at maximum output
current are given by:
Where δ∆T is the temperature dependency of R
k is a constant inversely related to the gate drive current.
Both MOSFETs have I
includes an additional term for transition losses, which are
highest at high input voltages. For V
current efficiency generally improves with larger MOSFETs,
while for V
to the point that the use of a higher R
lower C
chronous MOSFET losses are greatest at high input volt-
age or during a short circuit when the duty cycle in this
switch in nearly 100%. The term (1 + δ∆T) is generally
given for a MOSFET in the form of a normalized R
temperature curve, but δ = 0.005/°C can be used as an
approximation for low voltage MOSFETs. C
∆V
The constant k = 2 can be used to estimate the contribu-
tions of the two terms in the main switch dissipation
equation.
If the charger is to operate in low dropout mode or with a
high duty cycle greater than 85%, then the topside
P-channel efficiency generally improves with a larger
MOSFET. Using asymmetrical MOSFETs may achieve cost
savings or efficiency gains.
Main Switch Duty Cycle = V
Synchronous Switch Duty Cycle = (V
PMAIN = V
PSYNC = (V
DS
is usually specified in the MOSFET characteristics.
RSS
IN
actually provides higher efficiency. The syn-
+ k(V
DS(ON)
> 20V the transition losses rapidly increase
OUT
IN
– V
/V
IN
, total gate capacitance Q
U
)
IN
2
OUT
2
(I
(I
R losses while the PMAIN equation
RSS
MAX
MAX
)/V
U
, input voltage and maximum
)(C
)
IN
2
(1 + δ∆T)R
(I
RSS
OUT
MAX
)(f
/V
)
W
2
IN
OSC
(1 + δ∆T)R
IN
DS(ON)
IN
)
DS(ON)
< 20V the high
– V
RSS
device with
OUT
G
DS(ON)
U
, reverse
DS(ON)
DS(ON)
)/V
= Q
IN
and
GD
.
vs
/
The Schottky diode D1, shown in the Typical Application
on the back page, conducts during the dead-time between
the conduction of the two power MOSFETs. This prevents
the body diode of the bottom MOSFET from turning on and
storing charge during the dead-time, which could cost as
much as 1% in efficiency. A 1A Schottky is generally a
good size for 4A regulators due to the relatively small
average current. Larger diodes can result in additional
transition losses due to their larger junction capacitance.
The diode may be omitted if the efficiency loss can be
tolerated.
Calculating IC Power Dissipation
The power dissipation of the LTC4008 is dependent upon
the gate charge of the top and bottom MOSFETs (Q
Q
manufacturer’s data sheet and is dependent upon both the
gate voltage swing and the drain voltage swing of the
MOSFET. Use 6V for the gate voltage swing and V
the drain voltage swing.
Example:
Adapter Limiting
An important feature of the LTC4008 is the ability to
automatically adjust charging current to a level which
avoids overloading the wall adapter. This allows the prod-
uct to operate at the same time that batteries are being
charged without complex load management algorithms.
Additionally, batteries will automatically be charged at the
maximum possible rate of which the adapter is capable.
This feature is created by sensing total adapter output
current and adjusting charging current downward if a
preset adapter current limit is exceeded. True analog
G2
PD = V
V
I
PD = 292mW
Q
DCIN
respectively) The gate charge is determined from the
= 5mA
= 19V, f
DCIN
• (f
OSC
OSC
= 345kHz, Q
(Q
G1
+ Q
G2
) + I
G1
= Q
Q
)
LTC4008
G2
= 15nC,
DCIN
15
G1
4008fa
for
&