isl32610e Intersil Corporation, isl32610e Datasheet
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
isl32610e
Related parts for isl32610e
isl32610e Summary of contents
Page 1
... ESD Protected, 1.8V, Micro Power, +125°C, 1/8 Unit Load, RS-485/RS-422 Differential Receivers ISL32610E, ISL32611E, ISL32612E The ISL32610E, ISL32611E, ISL32612E are ±16.5kV IEC61000 ESD protected, fractional unit load (UL), 1.8V powered, single differential receivers (Rx) for balanced (e.g., RS-485) data communication. With their 85µA supply ...
Page 2
... ISL32610E, ISL32611E Truth Table (Note 12 NOTE: 5. Low Power Shutdown Mode (Note 10, except for the ISL32610E) QUIESCENT LOW POWER Rx ENABLE? I (µA) SHUTDOWN Yes, Active Low 85 Yes 85 Yes PACKAGE Tape & Reel ...
Page 3
... ISL32610E, ISL32611E, ISL32612E Pin Descriptions PIN NUMBER PIN NAME ISL32610E ISL32611E ISL32612E GND Typical Operating Circuit +1. GND 2 ISL32611E 3 1 System power supply input (1.8V to 3.6V). 2 Ground connection. 3 Receiver output > least 0.2V high < 0.2V or more low High if A and B are unconnected (floating) ...
Page 4
... ISL32610E, ISL32611E, ISL32612E Absolute Maximum Ratings V to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V CC Input Voltages RE -0. -8V to +12.5V Output Voltages RO -0. ESD Rating . . . . . . . . . . . . . . See “Electrical Specifications” Table page 5 Latch-up (per JESD78, Level 2, Class +125°C CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty ...
Page 5
... The ISL32611E enters SHDN whenever RE switches high, and the ISL32612E enters SHDN whenever RE switches low. 11. Devices meeting these limits are denoted as “1/8 unit load (1/8 UL)” transceivers. The RS-485 standard allows Unit Loads on the bus, so there can be 256 1/8 UL devices on a bus. 12. Not applicable to the ISL32610E. Test Circuits and Waveforms ...
Page 6
... ISL32610E, ISL32611E, ISL32612E Test Circuits and Waveforms SIGNAL A GENERATOR PARAMETER FIGURE 4A. TEST CIRCUIT FIGURE 4. RECEIVER ENABLE AND DISABLE TIMES (EXCLUDING ISL32610E) 6 (Continued) RE 1kΩ RE VCC GND SW 15pF +1V GND - +1V GND RO - ...
Page 7
... The result is a more repeatable and predictable test, but equipment limits prevent testing devices at voltages higher than ±9kV. The ISL32610E, ISL32611E, ISL32612E survive ±9kV contact discharges on the bus pins. FN7869.0 October 21, 2011 ...
Page 8
... ISL32610E, ISL32611E, ISL32612E Typical Performance Curves 1. LOW 0.2 0.4 0.6 0.8 1.0 RECEIVER OUTPUT VOLTAGE (V) FIGURE 5. RECEIVER OUTPUT CURRENT vs RECEIVER OUTPUT VOLTAGE (V = 1.8V) CC 120 110 V = 3.3V CC 100 1. -40 - TEMPERATURE (°C) FIGURE 7. STATIC SUPPLY CURRENT vs TEMPERATURE 2 DI ...
Page 9
... ISL32610E, ISL32611E, ISL32612E Typical Performance Curves A ∞ TIME (10µs/DIV) FIGURE 11. ISL32614E AND ISL32611E PERFORMANCE WITH V = 1.8V, 256kbps, 1000’ (305m) CAT 5 CABLE CC Die Characteristics SUBSTRATE POTENTIAL (POWERED UP) : GND PROCESS: Si Gate BiCMOS +25°C; Unless Otherwise Specified (Continued) ...
Page 10
... Intersil product families. For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page on intersil.com: ISL32610E, ISL32611E, ISL32612E To report errors or suggestions for this datasheet, please go to: FITs are available from our website at: Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted in the quality certifications found at Intersil products are sold by description only ...
Page 11
... ISL32610E, ISL32611E, ISL32612E Package Outline Drawing P5.064 5 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE Rev 3, 4/11 3 3.00 2.80 (1.90 (0.95) 0.50 0.30 0.20 (0.008 TOP VIEW 0.10 (0.004) C SIDE VIEW 5 (2.4) (2x 0.95) (1.90) TYPICAL RECOMMENDED LAND PATTERN 11 3.00 1.70 2.60 1.50 1.30 SEATING 1.45 0.90 PLANE 0.90 SEATING C PLANE 0.15 0.00 5x (0.60) 5x (1.2) 4 NOTES: 1. Dimensioning and tolerance per ASME Y14.5M-1994. ...
Page 12
... ISL32610E, ISL32611E, ISL32612E Package Outline Drawing P6.064 6 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE Rev 4, 2/10 1.90 0. PIN 1 INDEX AREA 0.40 ±0.10 0.20 TOP VIEW 3 2.90 ±0.10 SIDE VIEW (0.95) (2.40) TYPICAL RECOMMENDED LAND PATTERN 12 D 1.60 +0.15/-0.10 2. A-B D 1.15 +0.15/-0.25 C 0.10 C 0.00-0.15 (0.60) (1.20) NOTES: 1. Dimensions are in millimeters. Dimensions ...