isl22102 Intersil Corporation, isl22102 Datasheet - Page 7

no-image

isl22102

Manufacturer Part Number
isl22102
Description
Dual, Audio, Push-button Controlled Potentiometer Xdcp?
Manufacturer
Intersil Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
isl22102IR20Z
Manufacturer:
Intersil
Quantity:
50
Part Number:
isl22102IR20Z-TK
Manufacturer:
INTERSIL
Quantity:
20 000
Pin Descriptions
LEFT_IN, RIGHT_IN
The LEFT_IN and RIGHT_IN pins of the ISL22102 are
equivalent to the fixed terminals of a mechanical
potentiometer. The stereo audio signal applied to these pins
are referenced to VB and may have ±AVCC/2 maximum
amplitude.
LEFT_OUT, RIGHT_OUT
The LEFT_OUT and RIGHT_OUT pins are the buffered
wiper terminals of the potentiometers which are equivalent to
the movable terminals of a mechanical potentiometers with
attached unity gain operational amplifiers (Op Amp). The
default output position of wiper terminals preset to -20dB
attenuation of input signals.
VB
This is reference voltage output equal AVCC/2
common point for audio inputs, as well as reference signal
for other system components.
UP
The debounced active low UP input is increment the wipers
position of both channels. An on-chip 2µA current source
pull-up holds the UP input High. A switch closure to ground
or a Low logic level will after a debounce time and Zero
Amplitude Crossing Detection, move the wiper to the next
adjacent higher tap position. If the UP input signal is held
down for 1s, the wipers will auto increment their position with
a 4Hz frequency rate for 4s, and then a 8Hz frequency rate
(see Figure 2). When the wipers reach their top position of
0dB attenuation, they will stay at this position ignoring any
further Up commands.
DN
The debounced DN input is decrement the wipers position of
both channels. An on-chip 2µA current source pull-up holds
the DN input High. A switch closure to ground or a Low logic
level will, after a debounce time and Zero Amplitude
Crossing Detection, move the wiper to the next adjacent
lower tap position. If DN input signal is held down for 1s, the
wipers will auto decrement their position with a 4Hz
frequency rate for 4s, and then a 8Hz frequency rate. When
the wipers reach their bottom position of -90dB attenuation,
they will stay at this position ignoring any further Down or
Mute commands.
MUTE
The active low MUTE input allows to move both wipers, after
a debounce time and Zero Amplitude Crossing Detection, to
the highest attenuation level of -90dB in one step. An
on-chip 2µA current source pull-up holds the MUTE input
High. When MUTE is released, both wipers will be set at
position having prior Mute command.
7
.
It is used as
ISL22102
SB
The active low SB input allows totally disconnect DCP arrays
from their LEFT_IN and RIGHT_IN pins, and move both
wipers to position closest to VB pin (as shown in Figure 3). It
also sets ISL22102 in low power Standby mode. When SB
will be released, the both wipers will be set at position they
have prior Standby.
.
FLAG
This output pin provides status information to the rest of the
system about audio activity. It is High when at least one
audio input exceeds V
is Low. The FLAG output can be directly connected to SB pin
for automatical setting the ISL22102 in Standby mode.
D0-D2
These three digital input pins allow to program a delay time
for FLAG Low output up to 240s. Table 1 lists the D0-D2
settings and corresponding delay times (typical values).
CB
This low pass filter terminal requires an external capacitor to
GND. The value of this capacitor, together with 5MΩ internal
resistor divider, directly determines the PSRR (Power Supply
Rejection Ratio) of audio and VB outputs. A 1µF to 10µF
capacitor is recommended.
HPA, HPB
These two high pass filter terminals require an external
capacitor of 100nF or higher in-between.
D2
FIGURE 3. DCP CONNECTION IN STANDBY MODE
TABLE 1. FLAG PROGRAMMED DELAY SETTINGS
0
0
0
0
1
1
1
1
(RIGHT_IN)
LEFT_IN
VB
D1
0
0
1
1
0
0
1
1
TH
threshold, otherwise its output level
D0
0
1
0
1
0
1
0
1
(WIPER_RIGHT)
WIPER_LEFT
September 29, 2008
DELAY, (s)
120
150
180
210
240
60
90
0
FN6788.0

Related parts for isl22102