ad7147a-1acbz-r Analog Devices, Inc., ad7147a-1acbz-r Datasheet - Page 29
ad7147a-1acbz-r
Manufacturer Part Number
ad7147a-1acbz-r
Description
Captouch Programmable Controller For Single-electrode Capacitance Sensors
Manufacturer
Analog Devices, Inc.
Datasheet
1.AD7147A-1ACBZ-R.pdf
(68 pages)
- Current page: 29 of 68
- Download datasheet (2Mb)
GPIO INT OUTPUT CONTROL
The INT output signal can be controlled by the GPIO pin when
the GPIO is configured as an input. The GPIO is configured as
an input by setting the GPIO_SETUP bits in the interrupt enable
register to 01. See the
section for more information on how to configure the GPIO.
Enable the GPIO interrupt by setting the GPIO_INT_ENABLE
bit in Register 0x007 to 1, or disable the GPIO interrupt by
clearing this bit to 0. The GPIO status bit in the conversion-
complete interrupt status register reflects the status of the GPIO
Table 16. GPIO Interrupt Behavior
GPIO_INPUT_CONFIG
00 = Negative Level Triggered
00 = Negative Level Triggered
01 = Positive Edge Triggered
01 = Positive Edge Triggered
10 = Negative Edge Triggered
10 = Negative Edge Triggered
11 = Positive Level Triggered
11 = Positive Level Triggered
General-Purpose Input/Output (GPIO)
GPIO Pin
1
0
1
0
1
0
1
0
1
0
GPIO_INT_STATUS
0
1
0
1
1
0
Rev. 0 | Page 29 of 68
interrupt. This bit is set to 1 when the GPIO has triggered INT .
The bit is cleared upon reading the GPIO_INT_STATUS bit if the
condition that caused the interrupt is no longer present.
The GPIO interrupt can be set to trigger on a rising edge, falling
edge, high level, or low level at the GPIO input pin. Table 16 shows
how the settings of the GPIO_INPUT_CONFIG bits in the inter-
rupt enable (STAGE_LOW_INT_ENABLE) register affect the
behavior of INT .
Figure 42 to Figure 45 show how the interrupt output is cleared
upon a read from the GPIO_INT_STATUS bit.
0
0
1
0
INT
1
1
0
1
INT Behavior
Not triggered
Asserted while signal on GPIO pin is low
Pulses low at low-to-high GPIO transition
Not triggered
Pulses low at high-to-low GPIO transition
Not triggered
Asserted while signal on GPIO pin is high
Not triggered
AD7147A
Related parts for ad7147a-1acbz-r
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
CapTouch™ Programmable Controller for Single-Electrode Capacitance Sensors
Manufacturer:
Analog Devices
Datasheet:
Part Number:
Description:
Analog Divider
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Analog Front End For Adsl
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Lc2mos Complete, 12-bit Analog I/o System
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Cmos 4/8 Channel Analog Multiplexers
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Low Cost, Low Power Cmos General Purpose Analog Front End
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
2.5 V To 5.0 V Micropower, Precision Series Mode Voltage References
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Stereo, Single-supply 18-bit Integrated Dac
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Multichannel 24-bit, 192 Khz, Dac
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Ac?97 Soundmax Codec
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Complete Dual 18-bit 16 X Fs Audio Dac
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Sampleport Stereo Asynchronous Sample Rate Converters
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
U.s./international Modem Daa Line Codec Chipset
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Low Distortion 750 Mhz Closed-loop Buffer Amp
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
High Speed Active Load With Inhibit Mode
Manufacturer:
Analog Devices, Inc.
Datasheet: