nb6lq572 ON Semiconductor, nb6lq572 Datasheet - Page 5

• Manufacturer Part Number: nb6lq572
• Description: 2.5v / 3.3v Differential 4 1 Mux W/input Equalizer To 1 2 Lvpecl Clock/data Fanout / Translator
• Manufacturer: ON Semiconductor

NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
5. Input and Output parameters vary 1:1 with V
6. LVPECL outputs loaded with 50 W to V
7. Vth, V
8. Vth is applied to the complementary input when operating in single−ended mode.
9. V
10. V
Table 5. DC CHARACTERISTICS POSITIVE LVPECL OUTPUT
(Note 5)
POWER SUPPLY
LVPECL OUTPUTS
DIFFERENTIAL CLOCK INPUTS DRIVEN SINGLE−ENDED (Note 7) (Figures 5 and 6)
VREFAC
DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (Note 9) (Figures 7 and 8)
CONTROL INPUT (SELx Pin)
TERMINATION RESISTORS
V
I
V
V
V
V
V
V
V
V
V
V
V
I
I
V
V
I
I
R
Symbol
CC
IH
IL
IH
IL
CC
OH
OL
IH
IL
th
ISE
REFAC
IHD
ILD
ID
CMR
IH
IL
TIN
input signal.
IHD
CMR
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
, V
IH
min varies 1:1 with GND, V
ILD,
, V
Power Supply Voltage
Power Supply Current for V
Output HIGH Voltage (Note 6)
Output LOW Voltage (Note 6)
Single−ended Input HIGH Voltage
Single−ended Input LOW Voltage
Input Threshold Reference Voltage Range (Note 8)
Single−ended Input Voltage (V
Output Reference Voltage (100 mA Load)
Differential Input HIGH Voltage (IN
Differential Input LOW Voltage (IN
Differential Input Voltage (IN
Input Common Mode Range (Differential Configuration)
(Note 10) (Figure 9)
Input HIGH Current IN
Input LOW Current IN
Input HIGH Voltage for Control Pin
Input LOW Voltage for Control Pin
Input HIGH Current
Input LOW Current
Internal Input Termination Resistor (Measured from INx to VTx)
IL,,
V
ID
and V
and V
ISE
CMR
parameters must be complied with simultaneously.
parameters must be complied with simultaneously.
x
x
/IN
/IN
CMR
Characteristic
x
x
(VT
CC
(VT
x
max varies 1:1 with V
, IN
CC
IH
(Inputs and Outputs Open)
x
x
/VT
/VT
− 2 V for proper operation.
x
– V
) (V
x
x
CC
, IN
, IN
x
x
IL
Open)
IHD
Open)
.
)
x
x
)
)
– V
ILD
http://onsemi.com
)
CC
V
V
V
V
V
V
. The V
CC
CC
CC
CC
CC
CC
5
= 2.5 V
= 3.3 V
= 2.5 V
= 3.3 V
= 2.5 V
= 3.3 V
CMR
V
CC
range is referenced to the most positive side of the differential
= 2.375 V to 3.6 V, GND = 0 V, T
V
V
V
V
CC
CC
CC
th
2.375
1355
2155
1300
GND
1200
−150
−150
GND
−150
−150
1100
1150
Min
500
200
100
3.0
2.0
– 2000
45
– 1145
+ 100
– 1300
0
V
V
V
CC
CC
CC
1600
2400
1600
Typ
800
2.5
3.3
75
50
− 1700
– 1100
– 900
A
= −40°C to +85°C
V
V
V
V
V
V
V
CC
IHD
CC
CC
CC
th
CC
2.625
1700
2500
1000
1800
1200
1200
Max
V
V
V
110
150
150
150
150
3.6
0.8
55
– 1500
– 100
CC
CC
CC
– 800
– 100
– 900
– 100
– 50
Unit
mA
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mA
mA
mA
mA
W
V
V
V