nb6l72m ON Semiconductor, nb6l72m Datasheet
nb6l72m
Available stocks
Related parts for nb6l72m
nb6l72m Summary of contents
Page 1
... W terminations and 400 mV output swings when externally terminated with resistor The device is offered in a small 16-pin QFN package. The NB6L72M is a member of the ECLinPS MAX™ family of high performance clock and data management products. Features • ...
Page 2
... NB6L72M VTD0 VTD1 + SEL0 SEL1 Figure 1. Logic/Block Diagram http://onsemi.com GND ...
Page 3
... In the differential configuration when the input termination pin (VTDn) are connected to a common termination voltage or left open, and if no signal is applied on Dn/Dn input, then the device will be susceptible to self-oscillation. 2. All V and GND pins must be externally connected to a power supply for proper operation. CC NB6L72M Exposed Pad (EP) Table 1. INPUT/OUTPUT SELECT TRUTH TABLE SEL0* L ...
Page 4
... Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 3. JEDEC standard multilayer board - 2S2P (2 signal, 2 power) with 8 filled thermal vias under exposed pad. NB6L72M Characteristics Human Body Model Machine Model ...
Page 5
... V is applied to the complementary input when operating in single-ended mode and V parameters must be complied with simultaneously. IHD ILD, ID CMR 9. V minimum varies 1:1 with GND, V CMR CMR input signal. NB6L72M V = 2.375 V to 3.63 V, GND = 2.5 V ...
Page 6
... Device to device skew is measured between outputs under identical transition @ 0.5 GHz. 13. Additive RMS jitter with 50% duty cycle clock signal. 14. Additive peak-to-peak data dependent jitter with input NRZ data at PRBS23. 15. Input and output voltage swing is a single-ended measurement operating in differential mode. NB6L72M = 2.375 V to 3.63 V, GND = Characteristic ≤ ...
Page 7
... D Figure 6. Differential Inputs Driven Differentially IHD(MAX) V ILD(MAX) V IHD CMR ID V ILD V IHD(MIN) V ILD(MIN) GND Figure 8. V Diagram CMR NB6L72M VTD VTD Figure 3. Input Structure thmax thmin GND D D Figure 7. Differential Inputs Driven Differentially ...
Page 8
... GND NB6L72M 50 W Single-Ended Driver 50 W GND GND Figure 14. Capacitor-Coupled ) (VT Connected to V http://onsemi.com NB6L72M = Open GND Figure 11. LVDS Interface V CC NB6L72M = ...
Page 9
... Figure 17. Typical CML Termination for Output Driver and Device Evaluation ORDERING INFORMATION Device NB6L72MMNG NB6L72MMNR2G †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. NB6L72M versus Output OUTPP V ...
Page 10
... MILLIMETERS DIM MIN MAX A 0.80 1.00 A1 0.00 0.05 A3 0.20 REF b 0.18 0.30 D 3.00 BSC D2 1.65 1.85 E 3.00 BSC E2 1.65 1.85 e 0.50 BSC K 0.18 TYP L 0.30 0.50 SOLDERING FOOTPRINT* 3.25 0.128 0.30 EXPOSED PAD 0.012 1.50 0.059 0.30 0.012 0.50 0.02 mm SCALE 10:1 inches ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. NB6L72M/D ...