max9963bjccq-td Maxim Integrated Products, Inc., max9963bjccq-td Datasheet - Page 9

• Manufacturer Part Number: max9963bjccq-td
• Description: Quad Low-power 500mbps Ate Driver/comparator
• Manufacturer: Maxim Integrated Products, Inc.

ELECTRICAL CHARACTERISTICS (continued)
(V
perature coefficients are measured at T
Note 15: Rising edge to rising edge or falling edge to falling edge.
Note 16: Specified amplitude is programmed. At this pulse width, the output reaches at least 95% of its nominal (DC) amplitude.
Note 17: Specified amplitude is programmed. Maximum data rate specified in transitions per second. A square wave that reaches
Note 18: Crosstalk from any driver to the other three channels. Aggressor channel is driving 3V
Note 19: Indicative of switching speed from DHV_ or DLV_ to DTV_ and DTV_ to DHV_ or DLV_ when V
Note 20: Both high and low comparators are tested.
Note 21: Change in offset voltage over input range.
Note 22: Change in offset voltage with power supplies independently set to their minimum and maximum values.
Note 23: Unless otherwise noted, all prop delays are measured at 40MHz, V
Note 24: V
Note 25: Relative to propagation delay at V
CC
0
= +9.75V, V
DLV_ = 0V
R
DRIVER SMALL-SIGNAL RESPONSE
L
= 50Ω
The pulse width is measured at DATA_.
at least 95% of its programmed amplitude may be generated at one-half this frequency.
are in term mode with V
V
Z
V
from V
pulse width is measured at the crossing points of the differential outputs.
DTV_
S
CCO_ _
DUT_
= 50Ω, driver in term mode with V
EE
DUT_
< V
= 0 to 1V, V
t = 2.50ns/div
=2V. Open-collector outputs are also terminated (internally or externally) with R
= -5.25V, V
DLV_
_______________________________________________________________________________________
crossing calibrated CHV_/CLV_ threshold to the crossing point of differential outputs.
or V
CHV_
CCO_ _
DTV_
DHV_ =
200mV
DHV_ =
500mV
DHV_ =
100mV
DTV_
> V
= V
= 2.5V, SC1 = SC0 = 0, V
J
DHV_
= +70°C to +100°C, unless otherwise noted.) (Note 1)
CLV_
= 1.5V.
, switching speed is degraded by approximately a factor of 3.
= 0.5V. At this pulse width, the output reaches at least 90% of its DC voltage swing. The
CHV_
DTV_
0
= V
DLV_ = 0V
R
= 0V. Comparator outputs are terminated with 50Ω to GND at scope input with
CLV_
DRIVER LARGE-SIGNAL RESPONSE
L
= 50Ω
Quad, Low-Power, 500Mbps
= 1.5V. V
CPHV_
t = 2.50ns/div
= 7.2V, V
DUT_
ATE Driver/Comparator
Typical Operating Characteristics
= 200mV
CPLV_
DHV_ = 5V
DHV_ = 3V
DUT_
DHV_ = 1V
P-P
= -2.2V, T
= 0 to 2V, V
. Overdrive = 100mV.
J
= +85°C, unless otherwise noted. All tem-
CHV_
0
P-P
TERM
= V
into a 50Ω load. Victim channels
DRIVE TO TERM TRANSITION
CLV_
= 50Ω to V
R
L
DHV_ TO DTV_
DLV_ TO DTV_
DLV_
= 50Ω
= 1V, slew rate = 2V/ns,
t = 5.0ns/div
< V
CCO_ _
DTV_
. Measured
< V
DHV_
. If
9