max9546esat Maxim Integrated Products, Inc., max9546esat Datasheet - Page 2

• Manufacturer Part Number: max9546esat
• Description: Differential Video Interface Chipset
• Manufacturer: Maxim Integrated Products, Inc.

DC ELECTRICAL CHARACTERISTICS—MAX9546
(V
noted.) (Note 3)
Differential Video Interface Chipset
ABSOLUTE MAXIMUM RATINGS
(Voltages are referenced GND.)
V
IN and FAULT (MAX9546)......................... -0.3V to (V
OUT+, OUT- (MAX9546) (Note 1) .............................-2V to +16V
FAULT Short-Circuit Duration to
IN+, IN- (MAX9547) (Note 1).....................................-2V to +16V
IOUT, LOS, ZT+, ZT- (MAX9547) ...............-0.3V to (V
Differential Input Voltage (|V
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
2
Note 1: The Absolute Maximum Ratings of OUT+/OUT- for the MAX9546 and IN+/IN- for the MAX9547 are based on a single-fault
Note 2: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a 4-layer
Supply Voltage Range
Quiescent Supply Current
Voltage Gain
Input-Voltage Swing
Input Clamp Voltage
Input Clamp Current
Input Resistance
Output Common-Mode Voltage
Output Impedance
Output Fault Current
Power-Supply Rejection Ratio
FAULT Output Logic Level
FAULT Output Leakage Current
CC
V
CC
CC
_______________________________________________________________________________________
to GND ............................................................-0.3V to +11V
= +8.5V, R
or GND (MAX9546) .........................................Continuous
condition, i.e. only one output of MAX9546 (or both outputs together) is shorted to the battery, V
not survive a double-fault condition, i.e. OUT+ and OUT- shorted to different supplies.
board. For detailed information on package thermal considerations see www.maxim-ic.com/thermal-tutorial.
PARAMETER
L
= 220Ω between OUT+ and OUT-, T
IN+
- V
IN-
|) (MAX9547)...............+5V
SYMBOL
I
V
I
V
F(OUT)
PSRR
R
CLMP
V
CLMP
I
R
V
COM
A
OUT
CC
CC
IN
IN
V
Guaranteed by PSRR
No load
V
Guaranteed by A
(Note 5)
(Note 5)
(Notes 5, 6)
OUT+ and/or OUT- to +16V
OUT+ and/or OUT- to + (V
OUT+ and/or OUT- to +2V
OUT+ and/or OUT- to -2V
OUT+ and/or OUT- to +16V, V
unconnected
OUT+ or OUT- to -2V, V
V
10V (Note 7)
V
IN
CC
OL
CC
CC
= 1.2V
, I
from 7.5V to
+ 0.3V)
+ 0.3V)
SINK
A
= -40°C to +85°C. Typical values are at T
P-P
= 1.6mA (Note 8)
(Note 4)
CONDITIONS
V
IOUT, LOS Short-Circuit Duration to
Continuous Power Dissipation (T
θ
θ
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ..................................................... +150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Differential mode
Common mode
JC
JA
V
8-Pin SO-EP (derate 24.4mW/°C above +70°C) ......1951.2mW
CC
.................................................................................41.0°C/W
(Note 2).....................................................................7.0°C/W
CC
or GND (MAX9547) .........................................Continuous
CC
unconnected
- 2V)
CC
MIN
1.8
3.0
7.5
45
46
A
A
= +70°C)
CC
= +25°C, unless otherwise
TYP
3.46
3.25
0.01
or GND. The devices will
500
8.5
0.1
64
24
62
52
2
7
9
2
4
7
6
MAX
10.0
112
2.2
1.2
3.4
0.4
13
UNITS
V
mA
V/V
mA
µA
kΩ
dB
µA
P-P
Ω
V
V
V
V