ne5517 ON Semiconductor, ne5517 Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
ne5517
Manufacturer Part Number
ne5517
Description
Dual Operational Transconductance Amplifier
Manufacturer
ON Semiconductor
Datasheet
1.NE5517.pdf
(14 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ne5517AN
Manufacturer:
AMI
Quantity:
6 231
Part Number:
ne5517D
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
ne5517N
Manufacturer:
S
Quantity:
20 000
Voltage-Controlled Resistor (VCR)
proportional to the input voltage, a voltage variable resistor
can be made. Figure 26 shows how this is done. A voltage
presented at the R
This voltage is multiplied by g
through the R
where g
temperature. Figure 27 shows a Voltage Controlled Resistor
using linearizing diodes. This improves the noise
performance of the resistor.
Voltage-Controlled Filters
The circuit is a unity gain buffer until X
R/R
octave with the −3 dB point being defined by the given
equations. Operating in the same manner, a Voltage
Controlled High-Pass Filter is shown in Figure 29. Higher
order filters can be made using additional amplifiers as
shown in Figures 30 and 31.
Because an OTA is capable of producing an output current
Figure 28 shows a Voltage Controlled Low-Pass Filter.
A
. Then, the frequency response rolls off at a 6dB per
M
is approximately 19.21 mMHOs at room
X
terminals:
X
terminals forces a voltage at the input.
R
x
+
200W
g
R ) R
M
M
) R
200W
and thereby forces a current
V
OS
I
A
D
A
2
3
4
R
1kW
P
C
+
−
NE5517/A
Figure 27. VCR with Linearizing Diodes
+V
/g
NE5517, NE5517A, AU5517
−V
CC
+V
M
2
CC
CC
11
3
4
is equal to
NE5517/A
−V
http://onsemi.com
+V
CC
CC
11
6
Figure 26. VCR
I
O
5
10
1
R
X
Voltage-Controlled Oscillators
wave generator. With the indicated values a range from
2.0 Hz to 200 kHz is possible by varying I
to 10 mA.
to be above 5.0 V.
sawtooth pulse generator, as shown in Figure 33.
APPLICATION HINTS
I
mirror ratio should be as accurate as possible over the entire
current range. A current mirror with only two transistors is
not recommended. A suitable current mirror can be built
with a PNP transistor array which causes excellent matching
and thermal coupling among the transistors. The output
current range of the DAC normally reaches from 0 to
−2.0 mA. In this application, however, the current range is
set through R
ABC
30kW
C
Figure 32 shows a voltage-controlled triangle-square
The output amplitude is determined by I
Please notice the differential input voltage is not allowed
With a slight modification of this circuit you can get the
To hold the transconductance g
5
7
100kW
should be chosen not greater than 1.0 mA. The current
R
X
R
8
C
I
30kW
DACMAX
7
100kW
REF
R
8
10kW
+ 2 @
(10 kW) to 0 to −1.0 mA.
V
V
−V
+V
INT
C
INT
OUT
10kW
CC
CC
R
V
REF
R
REF
X
−V
+V
INT
V
INT
+
+ 2 @ 5V
C
CC
CC
R ) R A
g M @ R A
M
10kW
within the linear range,
ABC
+ 1mA
OUT
from 1.0 mA
× R
OUT
.