adc12041 National Semiconductor Corporation, adc12041 Datasheet - Page 3

• Manufacturer Part Number: adc12041
• Description: 12-bit Plus Sign 216 Khz Sampling Analog-to-digital Converter
• Manufacturer: National Semiconductor Corporation

5
6
10
9
4
27
12–20
23–26
28
1
2
3
11
7
8
21
22
Pin Number
SSOP Pkg.
PLCC and
Pin Descriptions
V
V
V
WMODE
SYNC
D0–D8
D9–D12
RD
CS
RDY
V
AGND
V
DGND
V
CLK
WR
Name
IN
IN
REF
REF
A
D
Pin
+
+
+
−
+
−
The analog ADC inputs. V
input into the ADC.
Positive reference input. The operating voltage range for this input is 1V
3 and Figure 4 ). This pin should be bypassed to AGND at least with a parallel combination of a 10
µF and a 0.1 µF (ceramic) capacitor. The capacitors should be placed as close to the part as
possible.
Negative reference input. The operating voltage range for this input is 0V
Figure 3 and Figure 4 ). This pin should be bypassed to AGND at least with a parallel combination of
a 10 µF and a 0.1 µF (ceramic) capacitor. The capacitors should be placed as close to the part as
possible.
The logic state of this pin at power-up determines which edge of the write signal (WR ) will latch in
data from the data bus. If tied low, the ADC12041 will latch in data on the rising edge of the WR
signal. If tied to a logic high, data will be latched in on the falling edge of the WR signal. The state of
this pin should not be changed after power-up.
The SYNC pin can be programmed as an input or an output. The Configuration register’s bit b4
controls the function of this pin. When programmed as an input pin (b4 = 1), a rising edge on this
pin causes the ADC’s sample-and-hold to hold the analog input signal and begin conversion. When
programmed as an output pin (b4 = 0), the SYNC pin goes high when a conversion begins and
returns low when completed.
13-bit Data bus of the ADC12041. D12 is the most significant bit and D0 is the least significant. The
BW(bus width) bit of the Configuration register (b3) selects between an 8-bit or 13-bit data bus width.
When the BW bit is cleared (BW = 0), D7–D0 are active and D12–D8 are always in TRI-STATE
When the BW bit is set (BW = 1), D12–D0 are active.
The clock input pin used to drive the ADC12041. The operating range is 0.05 MHz to 12 MHz.
WR is the active low WRITE control input pin. A logic low on this pin and the CS will enable the
input buffers of the data pins D12–D0. The signal at this pin is used by the ADC12041 to latch in
data on D12–D0. The sense of the WMODE pin at power-up will determine which edge of the WR
signal the ADC12041 will latch in data. See WMODE pin description.
RD is the active low read control input pin. A logic low on this pin and CS will enable the active
output buffers to drive the data bus.
CS is the active low Chip Select input pin. Used in conjunction with the WR and RD signals to
control the active data bus input/output buffers of the data bus.
RDY is an active low output pin. The signal at this pin indicates when a requested function has
begun or ended. Refer to section Functional Description and the digital timing diagrams for more
detail.
Analog supply input pin. The device operating supply voltage range is +5V
guaranteed only if the V
bypassed to AGND with a parallel combination of a 10 µF and a 0.1 µF (ceramic) capacitor. The
capacitors should be placed as close to the supply pins of the part as possible.
Analog ground pin. This is the device’s analog supply ground connection. It should be connected
through a low resistance and low inductance ground return to the system power supply.
Digital supply input pins. The device operating supply voltage range is +5V
guaranteed only if the V
bypassed to DGND with a parallel combination of a 10 µF and a 0.1 µF (ceramic) capacitor. The
capacitors should be placed as close to the supply pins of the part as possible.
Digital ground pin. This is the device’s digital supply ground connection. It should be connected
through a low resistance and low inductance ground return to the system power supply.
A
A
+ and V
+ and V
IN
+ is the non-inverting (positive) input and V
D
D
+ are connected to the same potential. This pin should be
+ are connected to the same potential. This pin should be
3
Description
IN
− is the inverting (negative)
V
±
V
±
REF
REF
10%. Accuracy is
10%. Accuracy is
+
−
V
V
A
REF
+ (see Figure
www.national.com
+ −1 (see
®
.