mpc5566 Freescale Semiconductor, Inc, mpc5566 Datasheet - Page 16

• Manufacturer Part Number: mpc5566
• Description: Mpc5566 High Performance Microcontroller
• Manufacturer: Freescale Semiconductor, Inc

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Spec
43a V
40
41
42
43
44
45
46
V
| V
V
If standby operation is not required, connect V
Applies to CLKOUT, external bus pins, and Nexus pins.
Maximum average RMS DC current.
Eight-way cache enabled (L1CSR0[CORG] = 0b0).
Average current measured on automotive benchmark.
Peak currents can be higher on specialized code.
High use current measured while running optimized SPE assembly code with all code and data 100% locked in cache
(0% miss rate) with all channels of the eMIOS and eTPU running autonomously, plus the eDMA transferring data continuously from
SRAM to SRAM. Higher currents are possible if an ‘idle’ loop that crosses cache lines is run from cache. Write code to avoid this
condition.
Four-way cache enabled (L1CSR0[CORG] = 0b1) or (L1CSR0[CORG] = 0b0 with L1CSR0[WAM] = 0b1, L1CSR0[WID] = 0b1111,
L1CSR0[WDD] = 0b1111, L1CSR0[AWID] = 0b1, and L1CSR0[AWDD] = 0b1).
Figure 3
Power requirements for the V
segments. Refer to
Power requirements for each I/O segment are dependent on the frequency of operation and load of the I/O pins on a particular I/O
segment, and the voltage of the I/O segment. Refer to
total power consumption of an I/O segment is the sum of the individual power consumptions for each pin on the segment.
Absolute value of current, measured at V
Weak pullup/down inactive. Measured at V
Maximum leakage occurs at maximum operating temperature. Leakage current decreases by approximately one-half for each 8
to 12
V
Up to 0.6 V during power up and power down.
Electrical Characteristics
16
DDE2
PP
SSA
DDA0
can drop to 3.0 V during read operations.
V
V
V
V
Analog input differential signal range (with common mode 2.5 V)
Operating temperature range, ambient (packaged)
Slew rate on power-supply pins
o
refers to both V
REF
SSSYN
RCVSS
DDF
RC33
C, in the ambient temperature range of 50
and V
– V
shows an illustration of the I
differential voltage
to V
to V
DDA1
to V
DDE3
to V
DD
DDSYN
| must be < 0.1 V.
SS
SS
differential voltage
are limited to 2.25–3.6 V only if EBTS = 0; V
Table 11
differential voltage
differential voltage
SSA0
differential voltage
and V
Table 9. DC Electrical Specifications (T
for values to calculate the power dissipation for a specific operation.
DD33
Characteristic
SSA1
supply depend on the frequency of operation, load of all I/O pins, and the voltages on the I/O
DD_STBY
. | V
MPC5566 Microcontroller Data Sheet, Rev. 2.0
IL
SSA0
DDE
and V
values interpolated for these temperature values.
STBY
– V
= 3.6 V and V
IH
o
SSA1
C to 125
.
to ground.
Table 10
| must be < 0.1 V.
o
C. Applies to pad types: pad_a and pad_ae.
DDEH
DDE2
for values to calculate power dissipation for specific operation. The
= 5.25 V. Applies to pad types: pad_fc, pad_sh, and pad_mh.
and V
V
A
T
V
V
DDE3
RC33
A
V
= T
SSSYN
RCVSS
V
DDF
= (T
Symbol
RH
V
L
have a range of 1.6–3.6 V if EBTS = 1.
– V
IDIFF
—
– V
L
– T
– V
– V
– V
to T
DDSYN
RL
DD
H
SS
SS
) (continued)
H
)
–100
–0.1
–2.5
Min
–50
–50
4.5
T
—
L
Freescale Semiconductor
0.1
Max
5.25
100
2.5
T
50
50
50
H
19
V/ms
Unit
mV
mV
mV
ο
V
V
V
C
o
C