dp83932c-20 National Semiconductor Corporation, dp83932c-20 Datasheet - Page 33
dp83932c-20
Manufacturer Part Number
dp83932c-20
Description
Mhz Sonictm Systems-oriented Network Interface Controller
Manufacturer
National Semiconductor Corporation
Datasheet
1.DP83932C-20.pdf
(98 pages)
- Current page: 33 of 98
- Download datasheet (2Mb)
4 0 SONIC Registers
4 3 4 Transmit Control Register
(RA
This register is used to program the SONIC’s transmit actions and provide status information after a packet has been transmit-
ted (Figure 4-7) At the beginning of transmission bits 15 14 13 and 12 from the TXpkt config field are loaded into the TCR to
configure the various transmit modes (see Section 3 5 1 1) When the transmission ends bits 10 – 0 indicate status information
and are set to a ‘‘1’’ when the corresponding condition is true These bits along with the number of collisions information are
written into the TXpkt status field at the end of transmission (see Section 3 5 1 2) Bits 9 and 5 are cleared after the TXpkt status
field has been written Bits 10 7 6 and 1 are cleared at the commencement of the next transmission while bit 8 is set at this
time
A hardware reset sets bits 8 and 0 to a ‘‘1’’ and bit 1 to a 0 This register is unaffected by a software reset
Bit
15
14
13
12
11
10
k
r
e
PINT POWC CRCI EXDIS
r w
5 0
15
read only r w
l
PINT PROGRAMMABLE INTERRUPT
This bit allows transmit interrupts to be generated under software control The SONIC will issue an interrupt (PINT in
the Interrupt Status Register) immediately after reading a TDA and detecting that PINT is set in the TXpkt config
field
Note In order for PINT to operate properly it must be set and reset in the TXpkt config field by alternating TDAs This is necessary because after
PINT has been issued in the ISR PINT in the Transmit Control Register must be cleared before it is set again in order to have the interrupt issued for
another packet The only effective way to do this is to set PINT to a 1 no more often than every other packet
POWC PROGRAM ‘‘OUT OF WINDOW COLLISION’’ TIMER
This bit programs when the out of window collision timer begins
0 timer begins after the Start of Frame Delimiter (SFD)
1 timer begins after the first bit of preamble
CRCI CRC INHIBIT
0 transmit packet with 4-byte FCS field
1 transmit packet without 4-byte FCS field
EXDIS DISABLE EXCESSIVE DEFERRAL TIMER
0 excessive deferral timer enabled
1 excessive deferral timer disabled
Must be 0
EXD EXCESSIVE DEFERRAL
Indicates that the SONIC has been deferring for 3 2 ms The transmission is aborted if the excessive deferral timer is
enabled (i e EXDIS is reset) This bit can only be set if the excessive deferral timer is enabled
e
r w
14
3h)
e
read write
r w
13
r w
12
PINT
POWC PROGRAMMED OUT OF WINDOW COLLISION TIMER
CRCI
EXDIS DISABLE EXCESSIVE DEFERRAL TIMER
EXD
DEF
NCRS NO CRS
CRSL
EXC
OWC
PMB
FU
BCM
PTX
Field
(Continued)
11
0
r
PROGRAMMABLE INTERRUPT
CRC INHIBIT
EXCESSIVE DEFERRAL
DEFERRED TRANSMISSION
CRS LOST
EXCESSIVE COLLISIONS
OUT OF WINDOW COLLISION
PACKET MONITORED BAD
FIFO UNDERRUN
BYTE COUNT MISMATCH
PACKET TRANSMITTED OK
FIGURE 4-7 Transmit Control Register
EXD
10
r
DEF NCRS CRSL EXC
9
r
8
r
33
Description
Meaning
7
r
6
r
OWC
5
r
4
0
r
PMB
3
r
FU
2
r
BCM
1
r
PTX
0
r
Related parts for dp83932c-20
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Freescale Semiconductor Technical Data
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Self-calibrating 12-bit Plus Sign Serial I/o A/d Converters With Mux And Sample/hold
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinum Tm Fractional N Rf / Integer N If Dual Low Power Frequency Synthesizer
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinum? 2.0 Ghz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinumtm 160 Mhz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Dual N-channel Enhancement Mode Field Effect Transistor
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Video Amplifier System (obsolete)
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Synchronous Step-up DC/DC Converter For White Led Applications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
CLC420 - High Speed, Voltage Feedback op Amp, Package: Lcc, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Monolithic Triple 4.5 CRT Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Differential Video Amplifier
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
ADC10061 - 10-Bit 600 NS A/D Converter With Input Multiplexer And Sample/Hold, Package: Soic Wide, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
DS36277 - Dominant Mode Multipoint Transceiver, Package: Soic Narrow, Pin Nb=8
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Quad High Speed Trapezoidal Bus Transceiver
Manufacturer:
National Semiconductor Corporation
Datasheet: