tcm1a106m ROHM Co. Ltd., tcm1a106m Datasheet - Page 4

• Manufacturer Part Number: tcm1a106m
• Description: Chip Tantalum Capacitors Bottom Surface Electrode Type
• Manufacturer: ROHM Co. Ltd.

○
TC Series M Case
Temperature
Stability
Surge voltage
Loading at
High temperature
Terminal
strength
c
www.rohm.com
2009 ROHM Co., Ltd. All rights reserved.
Item
Temp.
∆C / C
Df (tan δ)
L.C.
Temp.
∆C / C
Df (tan δ)
L.C.
Temp.
∆C / C
Df (tan δ)
L.C.
Appearance
L.C.
∆C / C
Df (tan δ)
Appearance
L.C.
∆C / C
Df (tan δ)
Capacitance
Appearance
TCM0G336
TCM0J226
TCM0J336
TCM0G336
TCM0J226
TCM0J336
TCM0G336
TCM0G336
TCM0J226
TCM0J336
−55 °C
Shall be satisfied the voltage on " Standard list "
+85 °C
Shall be satisfied the voltage on " Standard list "
Less than 1000% of initial value
+125 °C
Shall be satisfied the voltage on " Standard list "
Less than 1000% of initial value
There should be no significant abnormality.
Less than 200% of initial limit
Within ±20% of initial value
Less than 200% of initial limit
There should be no significant abnormality.
Less than 200% of initial limit
Less than 200% of initial limit
The measured value should be stable.
There should be no significant abnormality.
Others : Within +15/0% of initial value
Others : Within ±20% of initial value
Others : Within 0/−15% of initial value
Others : Within +20/0% of initial value
: Within ±15/−5% of initial value
: Within ±15/−5% of initial value
: Within ±15/−5% of initial value
: Within ±15/−5% of initial value
: Within ±30% of initial value
: Within ±30% of initial value
: Within 0/−30% of initial value
: Within +15/-5% of initial value
: Within ±30% of initial value
: Within +20/-5% of initial value
Performance
−
4/6
Test conditions (based on JIS C 5101−1 and JIS C 5101− 3)
As per 4.29 JIS C 5101-1
As per 4.13 JIS C 5101-3
As per 4.26JIS C 5101-1
As per 4.14JIS C 5101-3
Apply the specified surge voltage every 5±0.5 min.
for 30±5 s. each time in the atmospheric condition of 85±2°C.
Repeat this procedure 1,000 times.
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
As per 4.23 JIS C 5101-1
As per 4.15 JIS C 5101-3
After applying the rated voltage for 1000+36/0 h without
discontinuation via the serial resistance of 3Ω or less
at a temperature of 85±2°C, leave the sample at room
temperature / humidity for over 24h and measure the value.
As per 4.35 JIS C 5101-1
As per 4.9 JIS C 5101-3
A force is applied to the terminal until it bends to 1mm and
by a prescribed tool maintain the condition for 5s.
(See the figure below)
thickness=1.6mm
50
45
R230
20
45
F (Apply force)
(Unit : mm)
1
2009.11 - Rev.G
Data Sheet