cp2200 Silicon Laboratories, cp2200 Datasheet - Page 91
![no-image](/images/no-image-200.jpg)
cp2200
Manufacturer Part Number
cp2200
Description
Single-chip Ethernet Controller
Manufacturer
Silicon Laboratories
Datasheet
1.CP2200.pdf
(108 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CP2200
Manufacturer:
CITIZEN
Quantity:
10 000
Company:
Part Number:
CP2200
Manufacturer:
SILICON
Quantity:
4 000
Part Number:
CP2200
Manufacturer:
SILICONLABS/芯科
Quantity:
20 000
Company:
Part Number:
cp2200-GQ
Manufacturer:
SiliconL
Quantity:
1 120
Company:
Part Number:
cp2200-GQ
Manufacturer:
NEC
Quantity:
5 871
Company:
Part Number:
cp2200-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
cp2200-GQ
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Company:
Part Number:
cp2200-GQR
Manufacturer:
AD
Quantity:
8 700
Part Number:
cp2200-GQR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Important Note: When using auto-negotiation, the auto-negotiation enable bit, AUTONEG (PHYCF.4), must
Bit 7:
Bit 6:
Bit 5:
Bit 4:
Bit 3:
Bit 2:
Bit 1:
Bit 0:
PHYEN
R/W
Bit7
PHYEN: Physical Layer Enable
0: The physical layer is placed in a low-power state with limited functionality.
1: The physical layer is placed in a normal power state and is fully functional.
TXEN: Transmitter Enable
0: Physical Layer’s transmitter is placed in a low-power state. Packet transmission and Link Pulse
Generation Functions are disabled.
1. Physical layer’s transmitter is enabled.
RXEN: Receiver Enable
0: Physical layer’s receiver is placed in a low-power state. Packet reception is disabled.
1: Physical layer’s receiver is enabled.
DPLXMD: Full-duplex Mode Enable Bit
Note: This bit is read-only when Auto-Negotiation is enabled.
0: Half-duplex mode is selected.
1: Full-duplex mode is selected.
LBMD: Loopback Mode Enable Bit
Note: Loopback mode is automatically disabled if a jabber condition is detected.
0: Loopback mode is disabled.
1: Loopback mode is enabled.
LPRFAULT: Link Partner Remote Fault (Local Fault) Indicator
0: Normal operation.
1: The link partner has detected a link fault and has sent notification during auto-negotiation. This
condition can occur if the local transmitter is disabled and link pulses are no longer generated.
POLREV: Polarity Reversed Indicator
0: Incorrect link polarity has not been detected.
1: Incorrect link polarity detected. Link polarity has been automatically reversed.
LINKSTA: Link Status Indicator
0: Link is bad.
1: Link is good.
TXEN
R/W
be set to “1” prior to
clear one of the three enable bits (PHYEN, TXEN, and RXEN) to “0” then set it back to “1”.
Bit6
Register 70. PHYCN: Physical Layer Control Register
RXEN
R/W
Bit5
setting PHYEN, TXEN, and RXEN to 1. To restart auto-negotiation,
DPLXMD
R/W or RO
Bit4
LBMD
Rev. 1.0
R/W
Bit3
LPRFAULT POLREV
Bit2
R
Bit1
R
LINKSTA
Bit0
CP2200/1
R
00000000
Reset Value
Address:
0x78
91