mc13109 Freescale Semiconductor, Inc, mc13109 Datasheet
mc13109
Available stocks
Related parts for mc13109
mc13109 Summary of contents
Page 1
... Universal Cordless Telephone Subsystem IC The MC13109 integrates several of the functions required for a cordless telephone into a single integrated circuit. This significantly reduces component count, board space requirements, and external adjustments designed for use in both the handset and the base. Dual Conversion FM Receiver – ...
Page 2
... DA Out 6 R10 1. Clk_5. Gnd Out LS09 Gnd LS09 5.0V 2 MC13109 Figure 1. MC13109FB Test Circuit RX_Audio Ext_C_In TX_In Open C47 MIC_ 1.0 F Amp R28 Out 49.9k C30 R30 R29 C38 1.0 F 49.9k 49.9k 5.0nF V CCA Open LO1 C41 C42 0.47 5.0nF F C40 R27 1 ...
Page 3
... Out Clk_5.0V U1 Gnd LS09 LS09 MOTOROLA ANALOG IC DEVICE DATA MC13109 Figure 2. MC13109FTA Test Circuit RX_Audio TX_In Ext_C_In Open C47 1.0 F MIC_ R28 Amp 49.9k Out C30 C38 1.0 F R29 5.0nF 49.9k V CCA Open R30 C42 R27 C40 49 ...
Page 4
... POWER SUPPLY Static Current Active Mode ( 2.6 V) Active Mode ( 3.6 V) Receive Mode ( 2.6 V) Receive Mode ( 3.6 V) Standby Mode ( 2.6 V) Standby Mode ( 3.6 V) Inactive Mode ( 2.6 V) Inactive Mode ( 3 MC13109 Symbol Value Unit V CC – 0 5.5 Vdc T J – +150 C Min ...
Page 5
... Input Referred) Second Mixer 3rd Matched Impedance Order Intercept (Input Input Referred) Detector Output – Impedance MOTOROLA ANALOG IC DEVICE DATA MC13109 channel U.S., without the need for any external switching circuitry (see Figure 29). Input Measure Pin Pin Symbol Min Mix 1 Det Out V SIN – ...
Page 6
... Input Impedance – Output Impedance – Output High Voltage – 1 Output Low Voltage – 0 MC13109 The carrier detect threshold is programmable through the MPU interface. Input Measure Pin Pin Symbol Min Mix 1 In RSSI RSSI – ...
Page 7
... Volume Control Steps Programmable through MPU Interface MOTOROLA ANALOG IC DEVICE DATA MC13109 the half supply reference so the input and output swing capability will increase as the supply voltage increases. The volume control can be adjusted through the MPU interface. The “R x Audio In” input signal is ac coupled. ...
Page 8
... Conditions 2 1.0 kHz, External Resistors Set for Gain of 1.) Characteristic Condition Open Loop Gain – Gain Bandwidth – Maximum Output Swing 8 MC13109 resistors and capacitors are used to set the gain and frequency response. The “SA In” input is ac coupled. Input Measure Pin Pin Symbol Min Out V Omax – ...
Page 9
... –2.5 dBV Limiter Output Level ALC disabled MOTOROLA ANALOG IC DEVICE DATA MC13109 increases slowly (i.e., a sine wave is maintained). The Limiter circuit limits rapidly changing signal levels by clipping the signal peaks. The ALC and/or Limiter can be disabled through the MPU serial interface. ...
Page 10
... Line Regulation mA 2.6 to 5.5 V Load Regulation 2 1.0 mA Drop–Out Voltage MC13109 resistors and capacitors can be connected to set the gain and frequency response. The “Spl Amp In” input is ac coupled. Input Measure Pin Pin Symbol Min ...
Page 11
... Data Amp Output 10 0 –10 – 20 – 30 – 40 – 50 – 60 MOTOROLA ANALOG IC DEVICE DATA MC13109 Bandgap reference voltage. The “BD Out” pin is open collector and requires and external pull–up resistor Input Measure Pin Pin Symbol Ref Ref/ Threshold ...
Page 12
... V in > = –12 dBV, V out = 0 –10 –20 – –24 dBV, V out = –17 dBV (Slowly Changing ALC Signals) –40 –50 –80 –60 –50 –40 –30 COMPRESSOR LEVEL INPUT (dBV) Figure 7. MC13109FTA Internal I/O Block Diagram Spl T x Lim Amp Ref Out In Out ...
Page 13
... Lim Lim C1 MOTOROLA ANALOG IC DEVICE DATA MC13109 PIN FUNCTION DESCRIPTION Description – These pins form the PLL reference oscillator when connected to an external parallel–resonant crystal (10.24 MHz typical). The reference oscillator is also the second Local Oscillator ( for the RF receiver. ...
Page 14
... Zealand, U.K., Netherlands and China (see channel frequency tables in Appendix A). The 2nd local oscillator and reference divider provide the reference frequency for the R x and T x PLL loops. The 14 MC13109 Type Input Signal input for IF amplifier/limiter. Gnd Ground pin for RF section of the IC. ...
Page 15
... Output Voltage Low 0.7 mA Output Voltage High – 0. 7mA Tri–State Leakage Current V = 1.2 V Input Capacitance – Output Capacitance – MOTOROLA ANALOG IC DEVICE DATA MC13109 14–b Programmable T x Counter U.K. Base T x Phase T x Ref Detector 25 U.K. Handset U.K. Base Ref ...
Page 16
... The “Data” and “Clk” pins are used to load data into the shift register. Figure 10 shows “Data” and “Clk” pin timing. Data is clocked on positive clock transitions. 16 MC13109 Measure Pin Symbol EN, Clk ...
Page 17
... Inactive, Standby and Active Modes. Data can be loaded into the shift registers and latched into the latch registers in any of the operating modes. MOTOROLA ANALOG IC DEVICE DATA MC13109 Figure 13. Microprocessor Serial Interface V CC Data, Clk, EN ...
Page 18
... MHz 2230 1 12.00 MHz 2400 1 11.15 MHz 1784 1 11.15 MHz 446 4 11.15 MHz 446 25 18 MC13109 14–Bit T x Counter T x Counter Latch 14–Bit R x Counter R x Counter Latch MSB 12–Bit Reference Counter Reference Counter Latch 2–Bit 4–Bit Stdby R x Clk Out Volume Mode Mode Select Control 15– ...
Page 19
... Speaker Amp Muted 0 Normal Operation Power Saving Operating Modes When the MC13109 is used in a handset important to conserve power in order to prolong battery life. There are five modes of operation; Active Standby, Interrupt and Inactive. In Active Mode, all circuit blocks are powered ...
Page 20
... In some handset applications it may be desirable to power down all circuitry including the microprocessor (MPU). First put the MC13109 into the Inactive mode, which turns off the MPU Clock Output (see Figure 22), and then disable the microprocessor. In order to give the MPU adequate time to ...
Page 21
... MPU). 2.048 MHz MPU “Clk Out” Radiated Noise on Circuit Board The clock line running between the MC13109 and the 2.230 MHz microprocessor has the potential to radiate noise which can 2.400 MHz ...
Page 22
... MC13109 section of this document different carrier detect threshold value is desired, it can be set through the MPU interface as shown in Figure 27 below Bit #1 Bit #0 Control # ...
Page 23
... MOTOROLA ANALOG IC DEVICE DATA MC13109 schematic of the 1st LO tank circuit. Figure 30 shows the latch control bit values. The internal varactor temperature coefficient is 1800 ppm 8 cap control voltage = 1 req = 36 MHz). Customer is suggested to use a negative temperature coefficient capacitor in 1st LO tank circuit when the whole operating temperature range of – ...
Page 24
... Power–Up Defaults for Control and Counter Registers When the IC is first powered up, all latch registers are initialized to a defined state. The MC13109 is initially placed in the Rx mode with all mutes active and nothing disabled. The reference counter is set to generate a 5.0 kHz reference frequency from a 10 ...
Page 25
... Figure 37 versus AF out , N+D, N, AMR out –10 –20 –30 AMR –40 N+D –50 –60 –120 –100 –80 –60 – INPUT (dBm) MOTOROLA ANALOG IC DEVICE DATA MC13109 Figure 34 versus Receive Mode 8.0 6.0 4.0 2.0 0 4.5 5.0 2.5 3.0 Figure 36 versus Inactive Mode 4.5 5.0 2 ...
Page 26
... For step down at the input, decay time is defined as the time for the input to settle to 0.75X of the final steady state value Input 0 mV Attack Time 1.5X Final Value Output MC13109 Figure 40. First Mixer Third Order 0 –20 –40 –60 –80 –100 –40 –20 0 – ...
Page 27
... Motorola was negligent regarding the design or manufacture of the part. Motorola and Opportunity/Affirmative Action Employer. MOTOROLA ANALOG IC DEVICE DATA MC13109 OUTLINE DIMENSIONS FB SUFFIX PLASTIC PACKAGE CASE 848B– ...
Page 28
... BSC 0.177 BSC V 9.000 BSC 0.354 BSC V1 4.500 BSC 0.177 BSC W 0.200 REF 0.008 REF X 1.000 REF 0.039 REF MOTOROLA ANALOG IC DEVICE DATA *MC13109/D* MC13109 ...