isd4003 Winbond Electronics Corp America, isd4003 Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
isd4003
Manufacturer Part Number
isd4003
Description
Single-chip, Multiple-messages Voice Record/playback Devices 4-, 5-, 6-, And 8-minute Duration
Manufacturer
Winbond Electronics Corp America
Datasheet
1.ISD4003.pdf
(38 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
isd4003-04ME
Manufacturer:
NUVOTON
Quantity:
20 000
Part Number:
isd4003-04MEI
Manufacturer:
ISD
Quantity:
20 000
Part Number:
isd4003-04MEY
Manufacturer:
ISD
Quantity:
20 000
Company:
Part Number:
isd4003-04MEYI
Manufacturer:
NUVOTON
Quantity:
3 847
Company:
Part Number:
isd4003-04MP
Manufacturer:
ISD
Quantity:
25
Company:
Part Number:
isd4003-04MP
Manufacturer:
ISD
Quantity:
1 248
Part Number:
isd4003-04MP
Manufacturer:
ISD
Quantity:
20 000
Company:
Part Number:
isd4003-04MPY
Manufacturer:
ADI
Quantity:
4 493
Part Number:
isd4003-04MPY
Manufacturer:
ISD
Quantity:
20 000
6. PIN DESCRIPTION
[ ] 1
connected to this pin can drive a load as small as 5 KΩ. When in record, a built-in resistor connects AUD OUT to
the internal 1.2-volt analog ground supply. This resistor is approximately 850 KΩ, but will vary somewhat
according to the sample rate of the device. This relatively high impedance allows this pin to be connected to an
audio bus without loading it down.
AUD OUT
PIN NAME
V
The AUD OUT pin is always at 1.2 volts when the device is powered up. When in playback, the output buffer
SSA
MOSI
MISO
SS
NC
/ V
SSD
[ ] 1
5-10, 15,
11, 12,
SOIC /
23 / 4
19-22
PDIP
13
1
2
3
PIN NO.
16, 19, 21,
1, 17, 18 /
23, 27, 28
3, 4, 13-
TSOP
10
11
12
20
9
Slave Select: This input, when LOW, will select the
ISD4003 device.
Master Out Slave IN: This is the serial input to the
ISD4003 device when it is configured as slave. The master
microcontroller places data on the MOSI line one half-cycle
before the rising edge of SCLK for clocking into the device.
Master In Slave Out: This is the serial output (open drain)
of the ISD4003 device. This output goes into a high-
impedance state if the device is not selected.
Ground: The ISD4003 series utilizes separate analog and
digital ground busses. The analog ground (V
should be tied together as close as possible and connected
through a low-impedance path to power supply ground.
The digital ground (V
a separate low-impedance path to power supply ground.
These ground paths should be large enough to ensure that
the impedance between the V
less than 3 Ω. The backside of the die is connected to V
through the substrate. For chip-on-board design, the die
attach area must be connected to V
Not connected
Audio Output: This pin provides an audio output of the
stored data and is recommended be AC coupled. It is
capable of driving a 5 KΩ impedance R
- 7 -
SSD
Publication Release Date: July 16, 2007
FUNCTION
) pin should be connected through
ISD4003 SERIES
SSA
pins and the V
SS
or left floating.
EXT
.
Revision 1.3
SSD
SSA
) pins
pin is
SS