ada4320-1 Analog Devices, Inc., ada4320-1 Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
ada4320-1
Manufacturer Part Number
ada4320-1
Description
High Power, Low Distortion Upstream Catv Line Driver Ada4320-1
Manufacturer
Analog Devices, Inc.
Datasheet
1.ADA4320-1.pdf
(16 pages)
APPLICATIONS INFORMATION
GENERAL APPLICATIONS
The ADA4320-1 is primarily intended for use as the reverse
channel power amplifier (PA) in DOCSIS® 3.0 customer premises
equipment (CPE), including cable modems, E-MTAs, and
DOCSIS-enabled set-top boxes. The signals are typically QPSK or
QAM waveforms generated by the upstream modulator and DAC.
To sufficiently attenuate DAC images, a low-pass reconstruction
filter is recommended between the DAC output and the
ADA4320-1. A differential filter is preferred, and its output
impedance should match the 640 Ω input impedance of the
ADA4320-1.
Varying distances between the CPE and the cable modem
termination system (CMTS), as well as diplexers and splitters
that may exist in the signal path, require the amplifier to
provide a wide range of output power. The combination of a
high output level, excellent linearity, and 59 dB gain range of the
ADA4320-1 enables the CPE to overcome inline losses and
ensures adequate signal strength at the upstream termination.
CIRCUIT DESCRIPTION
In power-up mode, the ADA4320-1 comprises three analog
functions. The input amplifier (preamp) can be used single-ended
or balanced (differential). If the input is used in the balanced
configuration, it is imperative that the input signals be 180° out
of phase and of equal amplitude. A Vernier adjustment amplifier
controls the 1 dB gain steps.
The digital attenuator (DA) stage provides coarse adjustment in
6 dB steps. It also scales the current supplied to the output stage.
Both the preamp and DA are differential (balanced) to improve
power supply rejection and linearity.
The differential current is output from the DA to the output stage.
The output stage, with its 300 Ω balanced output impedance,
maintains proper matching to a 75 Ω load when used with a
2:1 (turns ratio) balun transformer.
PROGRAMMING
The ADA4320-1 is controlled via a unidirectional, 3-wire serial
interface (SPI-compatible) consisting of CLK, DATEN , and SDATA
signals. An 8-bit data-word containing the output stage current
level (Bits[7:6]) and desired gain code (Bits[5:0]) is clocked into
the SDATA port, MSB first.
The programmable current level (CL) range of the ADA4320-1 is
CL3 (highest) to CL0 (lowest). The programmable gain range is
+32 dB (Gain Code 60) to −27 dB (Gain Code 01), in steps of 1 dB
per least significant bit (LSB), providing a total gain range of 59 dB.
Rev. 0 | Page 11 of 16
Table 7. Data-Word for Setting Current and Gain Levels
CL
3
2
1
0
The sequence of loading the SDATA register starts on the falling
edge of the DATEN pin, which activates the CLK line. Data on
the SDATA line is clocked into the serial shift register on the
rising edge of CLK, MSB first. The data-word is latched into
the attenuator core on the rising edge of DATEN . Serial interface
timing for the ADA4320-1 is shown in
CURRENT LEVEL AND GAIN ADJUSTMENT
Gain adjustment and current scaling allow the PA to achieve the
high output levels and linearity required for multiple-channel
DOCSIS 3.0 compliance, while offering significantly reduced
power consumption in single-channel and lifeline battery-backup
modes of operation.
There are two methods of adjusting the output stage current of
the ADA4320-1. The first is performed automatically, lowering
output current as attenuation is increased (gain is reduced).
As shown in Figure 23, for every 6 dB reduction in gain, output
stage current is decreased. At higher gain settings, this is more
pronounced. At maximum gain and maximum current level,
a step down of 6 dB reduces the supply current by 33%.
The second method, which allows the user to program one of
four preset current levels (CL3 to CL0) at any gain setting, is
shown by the individual traces in Figure 23.
300
250
200
150
100
Typical
Current
(mA)
260 to 77
235 to 73
210 to 70
180 to 65
50
0
CURRENT LEVEL 3
CURRENT LEVEL 2
CURRENT LEVEL 1
CURRENT LEVEL 0
GAIN
Figure 23. Gain and Current Scaling
12
CL[7:6]
(Bin)
11
10
01
00
24
GAIN CODE
Gain[5:0]
(Hex)
3C to 01
3C to 01
3C to 01
3C to 01
36
Figure 2
Cain
Code
(Dec)
60 to 01
60 to 01
60 to 01
60 to 01
and
48
ADA4320-1
Figure 3
Typical
Gain (dB)
+32 to −27
+32 to −27
+32 to −27
+32 to −27
60
30
18
–6
–18
–30
6
.