el5174 Intersil Corporation, el5174 Datasheet
el5174
Available stocks
Related parts for el5174
el5174 Summary of contents
Page 1
... Generally, these pins are grounded but can be tied to any voltage reference. All outputs are short circuit protected to withstand temporary overload condition. The EL5174 is available package and EL5374 is available QSOP package. All specified for operation over the full -40°C to +85°C temperature range. Pinouts ...
Page 2
... Ordering Information PART NUMBER EL5174IS 5174IS EL5174IS-T7* 5174IS EL5174IS-T13* 5174IS EL5174ISZ (See Note) 5174ISZ EL5174ISZ-T7* (See Note) 5174ISZ EL5174ISZ-T13* (See Note) 5174ISZ EL5374IU EL5374IU EL5374IU-T7* EL5374IU EL5374IU-T13* EL5374IU EL5374IUZ (See Note) EL5374IUZ EL5374IUZ-T7* (See Note) EL5374IUZ EL5374IUZ-T13* (See Note) EL5374IUZ *Please refer to TB347 for details on reel specifications. ...
Page 3
... T Electrical Specifications +5V specified. PARAMETER DESCRIPTION AC PERFORMANCE BW -3dB Bandwidth BW ±0.1dB Bandwidth SR Slew Rate (EL5174) Slew Rate (EL5374) T Settling Time to 0.1% STL T Output Overdrive Recovery Time OVR GBWP Gain Bandwidth Product V BW (-3dB) V -3dB Bandwidth REF ...
Page 4
... EN PIN NAME FBP1 Feedback from non-inverting outputs INP1 Non-inverting inputs INN1 Inverting inputs, note that on EL5174, this pin is also the REF pin FBN1 Feedback from inverting outputs OUT1B, 2B, 3B Inverting outputs VSP Positive supply VSN Negative supply ...
Page 5
... INP1 INN1 REF1 INP2 INN2 REF2 INP3 INN3 REF3 SP1 SN1 SR1 SP2 SN2 SR2 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω EL5174 R F1 -5V 0Ω FBP 1 OUT 8 IN+ INP 2 VSN REF REF 3 VSP FBN 4 OUTB 5 50Ω ...
Page 6
... 500Ω 200Ω 10M FREQUENCY (Hz) FIGURE 5. FREQUENCY RESPONSE 6 EL5174, EL5374 = 200mV OP OP-P 100M 1G FIGURE 2. FREQUENCY RESPONSE FOR VARIOUS GAIN C = 23pF LD 100M 1kΩ F 100M 400M R = 1kΩ 2.7pF ...
Page 7
... CH1 <=> CH2, CH2 <=> CH3 -60 -70 -80 CH1 <=> CH3 -90 -100 10M 100k 1M FREQUENCY (Hz) FIGURE 11. CHANNEL ISOLATION (EL5374 ONLY) 7 EL5174, EL5374 (Continued) 10M 100M REF 10M 100M 1G FIGURE 10. VOLTAGE AND CURRENT NOISE vs FREQUENCY 100M 1G 0 -10 -20 -30 -40 PSRR- -50 ...
Page 8
... OP- for OP- -40 -50 -60 -70 -80 -90 -100 FREQUENCY (MHz) FIGURE 17. HARMONIC DISTORTION vs FREQUENCY 8 EL5174, EL5374 (Continued) HD2 (f = 20MHz) 3.5 4 4.5 5 FIGURE 14. HARMONIC DISTORTION vs DIFFERENTIAL 700 800 900 1000 HD3 ( 50mV/DIV FIGURE 18. SMALL SIGNAL TRANSIENT RESPONSE = ± ...
Page 9
... Typical Performance Curves 0.5V/DIV 10ns/DIV FIGURE 19. LARGE SIGNAL TRANSIENT RESPONSE M = 400ns, CH1 = 200mV/DIV, CH2 = 5V/DIV CH1 CH2 400ns/DIV FIGURE 21. DISABLED RESPONSE FIGURE 23. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE 9 EL5174, EL5374 (Continued) CH1 CH2 1.2 0.8 0.6 0.4 0.2 FIGURE 22. PACKAGE POWER DISSIPATION vs AMBIENT JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 1 ...
Page 10
... REF pin is from -3.3V to 3.7V. If the input common mode or differential mode signal is outside the above-specified ranges, it will cause the output signal distorted. The output of the EL5174 and EL5374 can swing from -3.8V to +3.8V at 1kΩ differential load at ±5V supply. As the load resistance becomes lower, the output swing is reduced. 10 ...
Page 11
... Power Dissipation G With the high output drive capability of the EL5174 and EL5374 possible to exceed the 135°C absolute maximum junction temperature under certain load current conditions. Therefore important to calculate the maximum junction temperature for the application to between 500Ω ...
Page 12
... MAX can solve the output current and R LD overheat. 12 EL5174, EL5374 Power Supply Bypassing and Printed Circuit Board Layout As with any high frequency device, a good printed circuit board layout is necessary for optimum performance. Lead lengths should be as sort as possible. The power supply pin must be well bypassed to reduce the risk of oscillation ...
Page 13
... REF L FBN 2R F ---------- - DC Gain = )Gain HF 1 -------------------------- = + || EL5174, EL5374 TWISTED PAIR EL5174/ EL5374 100Ω FIGURE 25. TWISTED PAIR CABLE RECEIVER FIGURE 26. TRANSMIT EQUALIZER IN+ EL5175/ EL5375 IN- REF ...
Page 14
... Plastic or metal protrusions of 0.006” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994 14 EL5174, EL5374 D (N/2)+1 (N/2) H ...
Page 15
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 15 EL5174, EL5374 M28.15 28 LEAD SHRINK SMALL OUTLINE PLASTIC PACKAGE M ...