ts391bl-al5-r Unisonic Technologies, ts391bl-al5-r Datasheet - Page 4

• Manufacturer Part Number: ts391bl-al5-r
• Description: Low Power Single Voltage Comparator
• Manufacturer: Unisonic Technologies

TS391/A/B/C
Supply Voltage
Differential Input Voltage
Input Voltage
Output Short-Circuit to Ground
Power Dissipation
Junction Temperature
Operating Temperature
Storage Temperature
Note 1. Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Thermal resistance from junction to Ambient
V
Input Offset Voltage
Differential Input Voltage
Large Signal Voltage Gain
Input Common Mode Voltage
Range
Low Level Output Voltage
Input Bias Current
Input Offset Current
Supply Current
Output sink current
High Level Output Current
Response Time
Large Signal Response Time
1. At output switch point, Vo=1.4V, Rs=0Ω with V
2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant,
3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than
4. Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains
5. The response time specified is for a 100mV input step with 5mV overdrive. For larger overdrive signals 300ns can
CC
V
independent of the state of the output, so no loading charge exists on the reference or input lines.
0.3V.The upper end of the common-mode voltage range is V
without damage.
within the common-mode range the comparator will provide a proper output state.
The low input voltage state must not be less than -0.3V (or 0.3V below the negative power supply, if used).
be obtained.
=5.0V, All voltage referenced to GND, Ta=25°C (unless otherwise specified)
CC
ELECTRICAL CHARACTERISTICS
2. Short-circuit from the output to V
ABSOLUTE MAXIMUM RATINGS
THARMAL DATA
1.5V).
3)
output current is approximately 20mA, independent of the magnitude of V
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
PARAMETER
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
2)
1)
PARAMETER
PARAMETER
4)
(T
1)
J
=150 , Ta=25
SYMBOL
V
V
V
I
I
I(BIAS)
I
℃
V
I(OFF)
I(DIFF)
trel
I(OFF)
Gv
I
SINK
I
I(CM)
CC
OH
tr
OL
CC
can cause excessive heating and eventual destruction. The maximum
Ta=+25℃
T
V
Ta=+25℃
T
V
V
Ta=+25℃
T
Ta=+25℃
T
V
V
V
V
V
R
V
MIN
MIN
MIN
MIN
℃)
CC
I(DIFF)
CC
CC
CC
I(DIFF)
I(DIFF)
CC
IN
L
=5.1kΩ to V
=TTL,V
=15V, R
= V
=5V, no load
=30V, no load
= V
CC
≤Ta≤ T
≤Ta≤ T
≤Ta≤ T
≤Ta≤ T
=1V,
=-1V, V
=1V,
from 5V ~ 30V and over the full input common-mode range(0V ~
OUT
OUT
TEST CONDITIONS
REF
=30V
=30V
MAX
L
MAX
MAX
MAX
=15k, V
=+1.4V,R
OUT
CC
=1.5V
SYMBOL
SYMBOL
5)
CC
V
OUT
T
T
V
Ta=+25℃
T
Ta=+25℃
T
I(DIFF)
V
θ
P
T
+ -1.5V,but either or both inputs can go to +30V
OPR
STG
MIN
MIN
CC
JA
IN
L
D
J
=1~ 11V
=5.1KΩ~ V
LINEAR INTEGRATED CIRCUIT
≤Ta≤ T
≤Ta≤ T
MAX
MAX
CC
CC
.
-40 ~ +125
-65 ~ +150
-0.3 ~ +36
±18 or 36
RATING
RATING
MIN
Infinite
50
0
0
6
±36
500
150
250
TYP
200
250
300
0.2
0.5
0.1
1.3
25
16
1
5
V
V
MAX
CC
1.25
V
400
700
250
400
150
CC
0.5
50
QW-R104-003,C
5
9
1
CC
-1.5
-2
°C /W
UNIT
UNIT
mW
°C
°C
°C
4 of 6
V
V
V
V/mV
UNIT
mV
mV
mV
mV
mA
mA
mA
nA
nA
nA
nA
nA
μA
μs
ns
V
V
V