s-8243bahft-tb-g Seiko Instruments Inc., s-8243bahft-tb-g Datasheet
s-8243bahft-tb-g
Related parts for s-8243bahft-tb-g
s-8243bahft-tb-g Summary of contents
Page 1
... V to 4.4 V (50 mV step) • Hysteresis voltage overcharge detection −0. −0.40 V (50 mV step (Overcharge release voltage n (= Overcharge detection voltage n + Hysteresis voltage n) can be selected within the range 3 4.4 V.) • Overdischarge detection voltage 2 3.0 V (100 mV step) • ...
Page 2
... BATTERY PROTECTION IC FOR 3-SERIAL OR 4-SERIAL CELL PACK S-8243A/B Series Block Diagrams 1. S-8243A Series VDD DOP COP 660 kΩ 440 kΩ VMP 660 kΩ VC1 VC2 VC3 VSS Remark1. Diodes in the figure are parasitic diodes. 2. Numerical values are typical values. 2 Battery protection ...
Page 3
... BATTERY PROTECTION IC FOR 3-SERIAL OR 4-SERIAL CELL PACK Rev.2.7 _00 2. S-8243B Series VDD DOP COP 660 kΩ 440 kΩ VMP 660 kΩ VC1 VC2 VC3 VSS Remark1. Diodes in the figure are parasitic diodes. 2. Numerical values are typical values. Battery protection DOP, COP, ...
Page 4
... CU 4.350 ±0.025 V S-8243BADFT-TB-G 4.350 ±0.025 V S-8243BAEFT-TB-G 4.250 ±0.025 V S-8243BAFFT-TB-G 4.315 ±0.025 V S-8243BAHFT-TB-G Note Change in the detection voltage is available in products other than listed above. Contact our sales office Table 1 S-8243A Series (For 3-Serial Cell) Hysteresis voltage for ...
Page 5
... Output pin for voltage regulator (3.3 V) Pin No. Symbol 1 VDD Input pin for positive power supply, Connection pin for battery 1’s positive voltage Connection pin for discharge control FET gate (CMOS output) 2 DOP Connection pin for charge control FET gate (Nch open drain output) ...
Page 6
... Board size : 114.3 mm × 76.2 mm × t1.6 mm (2) Board name : JEDEC STANDARD51-7 Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions. Figure 4 Power Dissipation of Package (When Mounted on Board) 6 ...
Page 7
... Temperature coefficient for T *2 overcurrent detection voltage 0 V BATTERY CHARGING FUNCTION (The 0 V battery function is either "0 V battery charging is allowed." or "0 V battery charging is inhibited." battery charge starting charger V voltage 0 V battery charge inhibition battery ...
Page 8
... Temperature coefficient for detection and release voltage is applied to overcharge detection voltage n, overcharge release voltage n, overdischarge detection voltage n, and overdischarge release voltage n. *2. Temperature coefficient for overcurrent detection voltage is applied to over current detection voltage 1 and 2. *3. Since products are not screened at high and low temperature, the specification for this temperature range is guaranteed by design, not tested in production. 8 ...
Page 9
... Temperature coefficient for T *2 overcurrent detection voltage 0 V BATTERY CHARGING FUNCTION (The 0 V battery function is either "0 V battery charging is allowed." or "0 V battery charging is inhibited." battery charge starting charger V voltage 0 V battery charge inhibition battery ...
Page 10
... Temperature coefficient for detection and release voltage is applied to overcharge detection voltage n, overcharge release voltage n, overdischarge detection voltage n, and overdischarge release voltage n. *2. Temperature coefficient for overcurrent detection voltage is applied to over current detection voltage 1 and 2. *3. Since products are not screened at high and low temperature, the specification for this temperature range is guaranteed by design, not tested in production. 10 ...
Page 11
... Test Circuits In this chapter test methods are explained for the case of S-8243B series, which is designed for 4-serial cell pack. For the case of S-8243A series, which is designed for 3-serial cell, voltage source V2 should be shorted, V3 should be read as V2, and V4 as V3. 1. Current consumption (Test circuit 1) Current consumption at not monitoring V 3 ...
Page 12
... Overcurrent detection voltages Starting condition 3.5 V, VMP = VDD, and the CDT pin is open. The DOP pin voltage thus provides “Low” The overcurrent detection voltage 1, VIOV1 is defined by the voltage difference VDD − VMP at which the DOP pin voltage becomes “ ...
Page 13
... One of the 0 V battery charge starting charger voltage and 0 V battery charge inhibition battery voltage is applied to each product according to the 0V battery charging function. Starting condition for a product in which 0 V battery charging is available. The COP pin voltage should be lower than V ...
Page 14
... Pin current for CTL2 at “High” Pin current for CTL2 at “Low” Pin current for CTL3 and CTL4 can be obtained in the same manner as in the CTL2. Pin current for COP at “High” pin current for COP at “Low” Pin current for DOP at “ ...
Page 15
... BATTERY PROTECTION IC FOR 3-SERIAL OR 4-SERIAL CELL PACK Rev.2.7 _00 VREG 16 1 VDD 2 DOP CTL1 15 3 COP CTL2 14 4 VMP CTL3 VC1 CTL4 VC2 VBATOUT VC3 CCT VSS CDT Test circuit 5 R1=1 MΩ 1 VDD 2 DOP 3 COP 4 VMP V1 5 VC1 ...
Page 16
... S-8243 enters the overcurrent status in which the DOP pin voltage becomes V IOV1 level to turn off the discharging FET to stop discharging, the COP pin becomes high impedance and is pulled up to EB+ pin voltage by an external resistor to turn off the charging FET to stop charging, and the VMP pin is pulled voltage by the internal resistor R ...
Page 17
... BATTERYn BATn After the state of CTL3 and CTL4 are changed, a time between 25 µs and 250 µs is needed for the battery monitor amp to become stable. Caution In the power down status the battery monitor amp output is the battery can be charged. 0CHA , 0 V battery can not be charged ...
Page 18
... S-8243A/B Series 4. CTL pins The S-8243 has four control pins. The CTL1 and CTL2 pins are used to control the COP and DOP pin output voltages. CTL1 takes precedence over CTL2. CTL2 takes precedence over the battery protection circuit. The CTL3 and CTL4 pins are used to control the VBATOUT pin output voltage ...
Page 19
... V SS Charger connected Load connected *2 Status *1. State depends on CTL3 and CTL4 input levels. Refer to Figure 9. *2. <1>: Normal status, <2>: Overcharge status, <3>: Overdischarge status, <4>: Power down status Remark The charger is assumed to charge with a constant current. V High-Z Overcharge detection Overdischarge detection delay time ( < ...
Page 20
... V SS Charger connected Load connected *3 Status * (typ.) RETURN DD *2. State depends on CTL3 and CTL4 input levels. Refer to Figure 9. *3. <1>: Normal status, <2>: Overcurrent status Remark The charger is assumed to charge with a constant current High-Z *1 RETURN Overcurrent detection ...
Page 21
... Voltage OPEN CTL2 pin OUT Voltage OPEN V SS *1. State depends on each battery voltage and the VMP pin voltage. *2. State depends on CTL3 and CTL4 input levels. Refer to Figure High-Z High-Z High-Z High-Z Figure 8 Seiko Instruments Inc. ...
Page 22
... OUT voltage OPEN CTL4 pin OUT voltage OPEN V SS *1. State depends on CTL1 and CTL2 and each battery voltage and the VMP pin voltage. Refer to Figure (1) (1) (1) (1) (1) (1) Don’t Don’t V1 × 0.2 use use V2 offset +V1 offset V1 × ...
Page 23
... Caution1. No resistance should be inserted in the power supply pin VDD. 2. The above constants are subject to change without prior notice has not been confirmed whether the operation is normal or not in circuits other than the above example of connection. In addition, the example of connection shown above and the constant will not guarantee successful operation ...
Page 24
... Caution1. No resistance should be inserted in the power supply pin VDD. 2. The above constants are subject to change without prior notice has not been confirmed whether the operation is normal or not in circuits other than the above example of connection. In addition, the example of connection shown above and the constant will not guarantee successful operation ...
Page 25
... Rev.2.7 _00 Precautions • Pay attention to the operating conditions for input/output voltage and load current so that the power loss in the IC does not exceed the package power dissipation. • Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic protection circuit. • ...
Page 26
... BATTERY PROTECTION IC FOR 3-SERIAL OR 4-SERIAL CELL PACK S-8243A/B Series The Example of Application Circuit 1. S-8243A Series 2. S-8243B Series Caution The above connection example will not guarantee successful operation. Perform thorough evaluation using the actual application. 26 CTL1 1 VDD VREG 16 S-8243A 2 DOP CTL1 15 3 COP ...
Page 27
... BATTERY PROTECTION IC FOR 3-SERIAL OR 4-SERIAL CELL PACK Rev.2.7 _00 Characteristics (Typical Data) 1. Current consumption S-8243BAF − OPE 120 100 [V] DD S-8243BAF − PDN 0.10 0.08 0.06 0.04 0. Overcharge detection/release voltage, overdischarge detection/release voltage, overcurrent ...
Page 28
... BATTERY PROTECTION IC FOR 3-SERIAL OR 4-SERIAL CELL PACK S-8243A/B Series S-8243BAF V IOV2 V Reference DD −0.40 −0.45 −0.50 −0.55 −0. [V] DD S-8243BAF − Temp V IOV3 0.575 0.550 0.525 0.500 0.475 0.450 0.425 −40 − [°C] S-8243BAF t − 1500 ...
Page 29
... BATTERY PROTECTION IC FOR 3-SERIAL OR 4-SERIAL CELL PACK Rev.2.7 _00 3. COP / DOP pin current S-8243BAF − COH 0.10 0.08 0.06 0.04 0.02 0. [V] COP S-8243BAF − DOH 0 − 1 − 2 − 3 − 4 − 1.8 3.6 5.4 V [V] DOP 4. Voltage regulator S-8243BAF − Temp V OUT 3.6 3.5 3.4 3.3 3.2 3.1 3.0 − 40 − [° ...
Page 30
... BATTERY PROTECTION IC FOR 3-SERIAL OR 4-SERIAL CELL PACK S-8243A/B Series 5. Battery monitor amp S-8243BAF V OFF 180 175 V 170 OFF1 V OFF2 165 160 155 V V OFF3 OFF4 150 [V] BAT S-8243BAF GAMP − Temp 0.202 GAMP4 0.201 GAMP3 0.200 ...
Page 31
...
Page 32
...
Page 33
...
Page 34
... Use of the information described herein for other purposes and/or reproduction or copying without the express permission of Seiko Instruments Inc. is strictly prohibited. The products described herein cannot be used as part of any device or equipment affecting the human body, such as exercise equipment, medical equipment, security systems, gas equipment, or any apparatus installed in airplanes and other vehicles, without prior written permission of Seiko Instruments Inc ...