lt3014bes5-trpbf Linear Technology Corporation, lt3014bes5-trpbf Datasheet
lt3014bes5-trpbf
Related parts for lt3014bes5-trpbf
lt3014bes5-trpbf Summary of contents
Page 1
... The device is available as an adjustable device with a 1.22V reference voltage. The LT3014 regulator is available in the 5-lead ThinSOT and 8-lead DFN packages. , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. ...
Page 2
LT3014 ABSOLUTE AXI U RATI GS IN Pin Voltage, Operating ................................. ±80V Transient (2ms Survival, LT3014HV) .............. +100V OUT Pin Voltage ............................................... ±60V IN to OUT Differential Voltage ........................... ±80V ADJ Pin Voltage .................................................. ±7V SHDN Pin ...
Page 3
ELECTRICAL CHARACTERISTICS The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are at T PARAMETER CONDITIONS Dropout Voltage I LOAD (Notes OUT(NOMINAL) LOAD I LOAD I LOAD I ...
Page 4
LT3014 W U TYPICAL PERFOR A CE CHARACTERISTICS Typical Dropout Voltage 500 450 400 T = 125°C J 350 300 T = 25°C 250 J 200 150 100 ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS SHDN Pin Current 1 25°C J CURRENT FLOWS OUT OF SHDN PIN 1.0 0.8 0.6 0.4 0 0.5 1 1.5 2 2.5 3 3.5 4 SHDN PIN VOLTAGE (V) ...
Page 6
LT3014 W U TYPICAL PERFOR A CE CHARACTERISTICS Minimum Input Voltage 3 20mA LOAD 3.0 2.5 2.0 1.5 1.0 0.5 0 –50 – 100 125 TEMPERATURE (°C) 3014 G19 10Hz to 100kHz Output Noise ...
Page 7
CTIO S (SOT-23 Package/DD Package) ADJ (Pin 4/Pin 2): Adjust. This is the input to the error amplifier. This pin is internally clamped to ±7V. It has a bias current of 4nA which flows into ...
Page 8
LT3014 U U APPLICATIO S I FOR ATIO Extra consideration must be given to the use of ceramic capacitors. Ceramic capacitors are manufactured with a variety of dielectrics, each with different behavior across temperature and applied voltage. The most common ...
Page 9
U U APPLICATIO S I FOR ATIO The LT3014 regulator has internal thermal limiting de- signed to protect the device during overload conditions. For continuous normal conditions the maximum junction temperature rating of 125°C must not be exceeded ...
Page 10
LT3014 U U APPLICATIO S I FOR ATIO The maximum junction temperature will then be equal to the maximum junction temperature rise above ambient plus the maximum ambient temperature or 50°C + 26°C = 76°C JMAX Example 2: ...
Page 11
U U APPLICATIO S I FOR ATIO In situations where the ADJ pin is connected to a resistor divider that would pull the ADJ pin above its 7V clamp voltage if the output is pulled high, the ADJ pin input ...
Page 12
LT3014 U TYPICAL APPLICATIO S 5V Buck Converter with Low Current Keep Alive Backup V IN 5.5V 60V 4.7µF 100V CERAMIC OPERATING CURRENT LOW HIGH 12 D2 D1N914 6 C2 † L1 0.33µF BOOST 15µ ...
Page 13
U TYPICAL APPLICATIO 12V 1µF (LATER 42V) OFF 48V (72V TRANSIENT) 1µF OFF ON Constant Brightness for Indicator LED over Wide Input Voltage Range LT3014 Automotive Application IN OUT NO PROTECTION LT3014 DIODE ...
Page 14
LT3014 PACKAGE DESCRIPTIO 0.62 MAX 3.85 MAX 2.62 REF RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.20 BSC DATUM ‘A’ 0.30 – 0.50 REF NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF ...
Page 15
... TOP MARK (NOTE 6) 0.200 REF Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights Package 8-Lead Plastic DFN (3mm × ...
Page 16
... I = 120µA, I <1µ 1.22V 0.30V 40µA, I <1µ 1.22V 0.30V 60µA, I <1µ 1.22V 0.30V 40µA, I <1µ 1.22V 0.30V 60µA, I <1µ LT/LWI 0706 REV B • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2005 3014fb ...