lt3014bes5-trpbf Linear Technology Corporation, lt3014bes5-trpbf Datasheet - Page 3

• Manufacturer Part Number: lt3014bes5-trpbf
• Description: 20ma, 3v To 80v Low Dropout Micropower Linear Regulator
• Manufacturer: Linear Technology Corporation

The
ELECTRICAL CHARACTERISTICS
PARAMETER
Dropout Voltage
V
GND Pin Current
V
(Notes 4, 6)
Output Voltage Noise
ADJ Pin Bias Current
Shutdown Threshold
SHDN Pin Current
(Note 8)
Quiescent Current in Shutdown
Ripple Rejection
Current Limit
Input Reverse
Leakage Current
Reverse Output Current
(Note 9)
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3014 is tested and specified for these conditions with the
ADJ pin connected to the OUT pin.
Note 3: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specification will not apply for
all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current, the input voltage
range must be limited.
Note 4: To satisfy requirements for minimum input voltage, the LT3014 is
tested and specified for these conditions with an external resistor divider
(249k bottom, 392k top) for an output voltage of 3.3V. The external
resistor divider adds a 5µA DC load on the output.
Note 5: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specified output current. In dropout, the
output voltage is equal to (V
IN
IN
= V
= V
●
OUT(NOMINAL)
OUT(NOMINAL)
denotes specifications which apply over the full operating temperature range, otherwise specifications are at T
(Notes 4, 5)
IN
– V
DROPOUT
).
CONDITIONS
I
I
I
I
I
I
I
I
I
I
I
I
I
C
(Note 7)
V
V
V
V
V
V
V
V
V
V
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
OUT
OUT
OUT
SHDN
SHDN
IN
IN
IN
IN
IN
OUT
= 6V, V
= 7V(Avg), V
= 7V, V
= 3.3V, ∆V
= –80V, V
= 0.47µF, I
= Off to On
= On to Off
= 1.22V, V
= 100µA
= 100µA
= 1mA
= 1mA
= 10mA
= 10mA
= 20mA
= 20mA
= 0mA
= 100µA
= 1mA
= 10mA
= 20mA
= 0V
= 6V
SHDN
OUT
OUT
OUT
= 0V
IN
LOAD
= 0V
RIPPLE
= 0V
< 1.22V (Note 2)
= –0.1V (Note 2)
= 20mA, BW = 10Hz to 100kHz
= 0.5V
P-P
, f
RIPPLE
Note 6: GND pin current is tested with V
source load. This means the device is tested while operating in its dropout
region. This is the worst-case GND pin current. The GND pin current
decreases slightly at higher input voltages.
Note 7: ADJ pin bias current flows into the ADJ pin.
Note 8: SHDN pin current flows out of the SHDN pin.
Note 9: Reverse output current is tested with the IN pin grounded and the
OUT pin forced to the rated output voltage. This current flows into the OUT
pin and out of the GND pin.
Note 10: The LT3014E is guaranteed to meet performance specifications
from 0°C to 125°C operating junction temperature. Specifications over
the –40°C to 125°C operating junction temperature range are assured by
design, characterization and correlation with statistical process controls.
Note 11: This IC includes overtemperature protection that is intended to
protect the device during momentary overload conditions. Junction
temperature will exceed 125°C when overtemperature protection is
active. Continuous operation above the specified maximum operating
junction temperature may impair device reliability.
= 120Hz, I
LOAD
= 20mA
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
MIN
0.25
60
25
IN
= V
OUT
TYP
120
200
300
350
250
650
115
1.3
1.3
(nominal) and a current
12
40
70
70
7
4
1
0
1
2
J
= 25°C.
LT3014
1000
MAX
180
250
270
360
350
450
410
570
100
450
20
30
10
2
4
1
4
6
4
µV
UNITS
3014fb
3
RMS
mV
mV
mV
mV
mV
mV
mV
mV
mA
mA
mA
µA
µA
µA
µA
µA
nA
µA
µA
µA
dB
µA
V
V