icl8068a Intersil Corporation, icl8068a Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
icl8068a
Manufacturer Part Number
icl8068a
Description
Precision 4 1/2 Digit, A/d Converter
Manufacturer
Intersil Corporation
Datasheet
1.ICL8068A.pdf
(23 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
icl8068aCDD
Manufacturer:
MICRO
Quantity:
300 000
Company:
Part Number:
icl8068aCJD
Manufacturer:
INTERSIL
Quantity:
5 510
Part Number:
icl8068aCJD
Manufacturer:
HARRIS
Quantity:
20 000
Applications
Specific Circuits Using the 8068A/71C03
8052A/A71C03
Figure 7 shows the complete circuit for a ±4
(±200mV full scale) A/D converter with LED readout using
the internal reference of the 8068A/52A. If an external
reference is used, the reference supply (pin 7) should be
connected to ground and the 300pF reference cap deleted.
The circuit also shows a typical RC input filter. Depending on
the application, the time-constant of this filter can be made
faster, slower, or the filter deleted completely. The
LED is driven from the 7-segment decoder, with a zero
reading blanked by connecting a D
the decoder.
A voltage translation network is connected between the
comparator output of the 8068A/52A and the auto-zero input
of the 71C03. The purpose of this network is to assure that,
during auto-zero, the output of the comparator is at or near the
threshold of the 71C03 logic (+2.5V) while the auto-zero
capacitor is being charged to V
instrument). Otherwise, even with 0V in, some reference
integrate period would be required to drive the comparator
output to the threshold level. This would show up as an
equivalent offset error. Once the divider network has been
selected, the unit-to-unit variation should contribute less than
a tenth of a count error. A second feature is the back-to-back
diodes, used to lower the noise. In the normal operating mode
they offer a high impedance and long integrating time
constant to any noise pulses charging the auto-zero cap. At
startup or recovery from an overload, their impedance is low
to large signals so that the cap can be charged up in one
auto-zero cycle. The buffer gain does not have to be set
precisely at 10 since the gain is used in both the integrate and
deintegrate phase. For scale factors other then 200mV the
gain of the buffer should be changed to give a ±2V buffer
output. For 2.0000V full scale this means unity gain and for
20,000mV (1µV resolution) a gain of 100 is necessary. Not all
8068As can operate properly at a gain of 100 since their offset
should be less than 10mV in order to accommodate the auto-
zero circuitry. However, for devices selected with less than
10mV offset, the noise performance is reasonable with
approximately 1.5µV near full scale. On all scales less than
200mV, the voltage translation network should be made
adjustable as an offset trim.
12
REF
5
(+100mV for a 200mV
ICL8052A/ICL71C03, ICL8068A/ICL71C03
signal to RBI input of
1
/
2
digit
1
/
2
digit
The auto-zero cap should be 1µF for all scales and the
reference capacitor should be 1µF times the gain of the
buffer amplifier. At this value if the input leakages of the
8052A/ 8068A are equal, the droop effects will cancel giving
zero offset. This is especially important at high temperature.
Some typical component values are shown in Table 1. For
3
V++ = +15V, V+ = 5V, V- = -15V
Clock Freq. = 120kHz (4
NOTE: Comment on offset limitations above. Buffer gain does not
improve ICL8052A noise performance adequately.
Full Scale V
Buffer Gain
R
C
C
C
V
Resolution (4
(
----------------------------------- -
1
RB1
INT
INT
AZ
REF
REF
/
2
SPECIFICATION
digit conversion, use 12kHz clock.
RB2
+
RB2
IN
)
1
/
2
Digit)
1
Note)
(See
0.22
100
100
/
TABLE 1.
1.0
20
10
10
2
1
Digit) or 12kHz (3
VALUE
0.22
200
100
100
1.0
10
10
10
2000
1000
0.22
100
100
1.0
1.0
1
1
/
2
Digit)
UNITS
V/V
mV
mV
kΩ
µV
µF
µF
µF