atxmega192a1-au ATMEL Corporation, atxmega192a1-au Datasheet - Page 23
atxmega192a1-au
Manufacturer Part Number
atxmega192a1-au
Description
8/16-bit Xmega A1 Microcontroller
Manufacturer
ATMEL Corporation
Datasheet
1.ATXMEGA192A1-AU.pdf
(113 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATXMEGA192A1-AU
Manufacturer:
ATMEL
Quantity:
340
- Current page: 23 of 113
- Download datasheet (4Mb)
12. System Control and Reset
12.1
12.2
12.3
12.3.1
12.3.2
12.3.3
12.3.4
12.3.5
8067M–AVR–09/10
Features
Resetting the AVR
Reset Sources
Power-On Reset
External Reset
Watchdog Reset
Brown-Out Reset
PDI reset
•
•
•
During reset, all I/O registers are set to their initial values. The SRAM content is not reset. Appli-
cation execution starts from the Reset Vector. The instruction placed at the Reset Vector should
be an Absolute Jump (JMP) instruction to the reset handling routine. By default the Reset Vector
address is the lowest Flash program memory address, ‘0’, but it is possible to move the Reset
Vector to the first address in the Boot Section.
The I/O ports of the AVR are immediately tri-stated when a reset source goes active.
The reset functionality is asynchronous, so no running clock is required to reset the device.
After the device is reset, the reset source can be determined by the application by reading the
Reset Status Register.
The MCU is reset when the supply voltage VCC is below the Power-on Reset threshold voltage.
The MCU is reset when a low level is present on the RESET pin.
The MCU is reset when the Watchdog Timer period expires and the Watchdog Reset is enabled.
The Watchdog Timer runs from a dedicated oscillator independent of the System Clock. For
more details see
The MCU is reset when the supply voltage VCC is below the Brown-Out Reset threshold voltage
and the Brown-out Detector is enabled. The Brown-out threshold voltage is programmable.
The MCU can be reset through the Program and Debug Interface (PDI).
Multiple reset sources for safe operation and device reset
Asynchronous reset
Reset status register
– Power-On Reset
– External Reset
– Watchdog Reset
– Brown-Out Reset
– PDI reset
– Software reset
– No running clock in the device is required for reset
The Watchdog Timer runs from separate, dedicated oscillator
Accurate, programmable Brown-Out levels
“WDT - Watchdog Timer” on page
24.
XMEGA A1
23
Related parts for atxmega192a1-au
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: