el2166 Intersil Corporation, el2166 Datasheet
el2166
Available stocks
Related parts for el2166
el2166 Summary of contents
Page 1
... V = ±5V The EL2166 has a superior output disable function. Time to enable or disable is < 75ns. The DISABLE pin is TTL/CMOS compatible. In disable mode, the amplifier can withstand over 1500V/µs signals at their outputs. The amplifier can operate on any supply voltage from 10V (±5V) to 33V (± ...
Page 2
... DISABLE Pin Voltage for IH Output Enabled (Note 6) V DISABLE Pin Threshold for Output Disabled IL 2 EL2166 = 25°C) Voltage at IN+, IN-, V DISABLE, GND Pins . . . . . . . . . . . . . . . (V Internal Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . See Curves Operating Ambient Temperature Range . . . . . . . . . .-40°C to +85°C Operating Junction Temperature Plastic Packages . . . . . . . . . 150°C Storage Temperature Range . . . . . . . . . . . . . . . . . .-65° ...
Page 3
... V = ±15V, and V OUT S OUT 5. A heat sink is required to keep junction temperature below absolute maximum when an output is shorted. 6. The EL2166 will remain ENABLED if pin 8 is either left unconnected or VIH is applied to pin 8. Closed-Loop AC Electrical Specifications PARAMETER DESCRIPTION BW -3dB Bandwidth (Note 1) SR ...
Page 4
... Typical Performance Curves Non-Inverting Frequency Response (Gain) Inverting Frequency Response (Gain) 3dB Bandwidth vs Supply Voltage for EL2166 Non-Inverting Frequency Frequency Response Response (Phase) for Various R Inverting Frequency Frequency Response for Response (Phase) Various R Peaking vs Supply Voltage 3dB Bandwidth vs for A ...
Page 5
... Typical Performance Curves 3dB Bandwidth vs Supply Voltage for 3dB Bandwidth vs Supply Voltage for 3dB Bandwidth vs Supply Voltage for EL2166 (Continued) Peaking vs Supply Voltage for Peaking vs Supply Voltage for Peaking vs Supply Voltage for A = +10 V 3dB Bandwidth vs ...
Page 6
... Typical Performance Curves Frequency Response for Various C L 2nd and 3rd Harmonic Distortion vs Frequency 6 EL2166 (Continued) Frequency Response for Various C IN- Transimpedance ( Frequency Closed-Loop Output Transimpedance (R Impedance vs Frequency vs Die Temperature PSRR and CMRR vs Frequency Voltage and Current Noise vs Frequency ) OL ...
Page 7
... Typical Performance Curves Offset Voltage vs Die Temperature +Input Resistance vs Die Temperature Output Voltage Swing vs Die Temperature 7 EL2166 (Continued) Supply Current vs Die Temperature Input Current vs Die Temperature Short Circuit Current vs Die Temperature Supply Current vs Supply Voltage +Input Bias Current vs Input Voltage PSRR & CMRR ...
Page 8
... Typical Performance Curves Differential Gain vs DC Input Voltage 150 L Differential Gain vs DC Input Voltage 500 L Slew Rate vs Supply Voltage 8 EL2166 (Continued) Differential Phase vs DC Input Voltage 150 L Differential Phase vs DC Input Voltage 500 L Slew Rate vs Temperature Small Signal Pulse Response Large Signal ...
Page 9
... Long Term Settling Error ENABLE Response for a Family of D.C. Inputs 150 Burn-In Circuit 9 EL2166 (Continued) 8-Pin Plastic DIP Maximum Power Dissipation vs Ambient Temperature DISABLE Response for a Family of D.C. Inputs = ±15V EL2166 8-Pin Plastic SO Maximum Power Dissipation vs Ambient Temperature = + 150 ±15V L S ...
Page 10
... Differential Gain and Phase Test Circuit Simplified Schematic 10 EL2166 ...
Page 11
... AC couple the signal ensure the driving signal is within the common mode range of the EL2166. Disable Function The EL2166 has a superior disable function that has been optimized for video performance. Time to disable/enable is around 75ns. During disable, the output of the EL2166 can withstand over 1500V/µ ...
Page 12
... The EL2166 is not slew rate limited, therefore any size step up to ±10V gives approximately the same settling time. As can be seen from the Long Term Settling Error curve, for A = +1, there is approximately a 0 ...
Page 13
... V OUT Current Limit The EL2166 has an internal current limit that protects the OUT circuit in the event of the output being shorted to ground. This limit is set at 80mA nominally and reduces with junction temperature junction temperature of 150°C, the current limits at about 50mA. If the output is shorted to ground, the power dissipation could be well over 1W ...
Page 14
... EL2166/ Input Stage * 1.0 vis vxx 1 130 25nH iinp 3 0 0.5µA iinm 2 0 5µA r12 3 0 2Meg * * Slew Rate Limiting * vis 600 dclamp dclamp ...
Page 15
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 15 EL2166 ...