ca5130a Intersil Corporation, ca5130a Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
ca5130a
Manufacturer Part Number
ca5130a
Description
15mhz, Bimos Microprocessor Operational Amplifiers With Mosfet Input/cmos Output
Manufacturer
Intersil Corporation
Datasheet
1.CA5130A.pdf
(19 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ca5130aE
Manufacturer:
HARRIS
Quantity:
5 510
Company:
Part Number:
ca5130aE
Manufacturer:
LT
Quantity:
5 510
Part Number:
ca5130aM
Manufacturer:
INTERSIL
Quantity:
20 000
Offset Nulling
Offset voltage nulling is usually accomplished with a 100,000
potentiometer connected across Terminals 1 and 5 and with the
potentiometer slider arm connected to Terminal 4. A fine offset
null adjustment usually can be effected with the slider arm
positioned in the midpoint of the potentiometer's total range.
Input Current Variation with Temperature
The input current of the CA5130 Series circuits is typically
5pA at 25
leakage current through the gate protective diodes in the input
circuit. As with any semiconductor junction device, including
op amps with a junction FET input stage, the leakage current
approximately doubles for every 10
temperature. Figure 25 provides data on the typical variation
of input bias current as a function of temperature in the
CA5130.
In applications requiring the lowest practical input current
and incremental increases in current because of “warm-up”
effects, it is suggested that an appropriate heat sink be used
with the CA5130. In addition, when “sinking” or “sourcing”
significant output current the chip temperature increases,
causing an increase in the input current. In such cases, heat-
sinking can also very markedly reduce and stabilize input
current variations.
Input Offset Voltage (V
Device Operating Life
It is well known that the characteristics of a MOS/FET device
can change slightly when a DC gate source bias potential is
applied to the device for extended time periods. The
magnitude of the change is increased at high temperatures.
Users of the CA5130 should be alert to the possible impacts
of this effect if the application of the device involves extended
operation at high temperatures with a significant differential
DC bias voltage applied across Terminals 2 and 3. Figure 26
shows typical data pertinent to shifts in offset voltage
encountered with CA5130 devices (metal can package)
during life testing. At lower temperatures (metal can and
plastic packages), for example at 85
is considerably less. In typical linear applications where the
differential voltage is small and symmetrical, these
incremental changes are of about the same magnitude as
those encountered in an operational amplifier employing a
bipolar transistor input stage. The 2V differential voltage
example represents conditions when the amplifier output
stage is “toggled”, e.g., as in comparator applications.
Power-Supply Considerations
Because the CA5130 is very useful in single supply
applications, it is pertinent to review some considerations
relating to power supply current consumption under both
single and dual supply service. Figures 1A and 1B show the
CA5130 connected for both dual and single supply operation.
o
C. The major portion of this input current is due to
IO
) Variation with DC Bias vs
7
o
o
C increase in
C, this change in voltage
CA5130, CA5130A
Dual supply operation: When the output voltage at Terminal
6 is 0V, the currents supplied by the two power supplies are
equal. When the gate terminals of Q
increasingly positive with respect to ground, current flow
through Q
increased and current flow through Q
supply) decreases correspondingly. When the gate terminals
of Q
to ground, current flow through Q
flow through Q
Single supply operation: Initially, let it be assumed that the
value of R
terminal bias (Terminals 2 and 3) is such that the output
terminal (No. 6) voltage is at V+/2, i.e., the voltage drops across
Q
quiescent supply current vs supply voltage for the CA5130
operated under these conditions. Since the output stage is
operating as a Class A amplifier, the supply current will remain
constant under dynamic operating conditions as long as the
transistors are operated in the linear portion of their voltage
transfer characteristics (see Figure 15). If either Q
swung out of their linear regions toward cutoff (a nonlinear
region), there will be a corresponding reduction in supply
current. In the extreme case, e.g., with Terminal 8 swung down
to ground potential (or tied to ground), NMOS transistor Q
completely cut off and the supply current to series connected
FIGURE 1. CA5130 OUTPUT STAGE IN DUAL AND SINGLE
8
and Q
8
FIGURE 1B. SINGLE POWER SUPPLY OPERATION
and Q
FIGURE 1A. DUAL POWER SUPPLY OPERATION
12
L
12
3
2
3
2
is very high (or disconnected), and that the input
12
are of equal magnitude. Figure 16 shows typical
POWER SUPPLY OPERATION
(from the negative supply) to the load is
12
are driven increasingly negative with respect
is decreased accordingly.
CA5130
CA5130
+
+
-
-
8
8
V+
V+
V-
7
4
7
4
Q
Q
Q
Q
8
12
8
12
8
is increased and current
8
8
and Q
(from the positive
6
6
12
are driven
8
R
R
or Q
L
L
12
12
are
is