xr16v2551im Exar Corporation, xr16v2551im Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/2/243/exar_corporation_sml.jpg)
xr16v2551im
Manufacturer Part Number
xr16v2551im
Description
High Performance Duart With 16-byte Fifo And Powersave Feature
Manufacturer
Exar Corporation
Datasheet
1.XR16V2551IM.pdf
(51 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
xr16v2551im-F
Manufacturer:
Exar Corporation
Quantity:
10 000
Pin Description
XR16V2551
HIGH PERFORMANCE DUART WITH 16-BYTE FIFO AND POWERSAVE FEATURE
MODEM OR SERIAL I/O INTERFACE
RXRDYB#
RXRDYA#
TXRDYB#
TXRDYA#
DSRA#
RTSA#
CTSA#
DTRA#
CDA#
N
INTB
RIA#
RXA
TXA
AME
32-QFN
P
21
23
25
IN
5
4
-
-
-
-
-
-
-
-
#
48-TQFP
P
29
43
31
18
33
38
34
39
40
41
IN
6
7
5
#
T
YPE
O
O
O
O
O
O
O
O
I
I
I
I
I
UART channel B Interrupt output. The output state is defined by the user through
the software setting of MCR[3]. INTB is set to the active mode and OP2B# output
LOW when MCR[3] is set to a logic 1. INTB is set to the three state mode and
OP2B# output HIGH when MCR[3] is set to a logic 0 (default). See MCR[3].
UART channel A Transmitter Ready (active low). The output provides the TX FIFO/
THR status for transmit channel A. See
nected.
UART channel A Receiver Ready (active low). This output provides the RX FIFO/
RHR status for receive channel A. See
nected.
UART channel B Transmitter Ready (active low). The output provides the TX FIFO/
THR status for transmit channel B. See
nected.
UART channel B Receiver Ready (active low). This output provides the RX FIFO/
RHR status for receive channel B. See
nected.
UART channel A Transmit Data or infrared encoder data. Standard transmit and
receive interface is enabled when MCR[6] = 0. In this mode, the TX signal will be
HIGH during reset or idle (no data). Infrared IrDA transmit and receive interface is
enabled when MCR[6] = 1. In the Infrared mode, the inactive state (no data) for the
Infrared encoder/decoder interface is LOW. If it is not used, leave it unconnected.
UART channel A Receive Data or infrared receive data. Normal receive data input
must idle HIGH. The infrared receiver pulses typically idles at LOW but can be
inverted by software control prior going into the decoder, see MCR[6]. If this pin is
not used, tie it to VCC or pull it high via a 100k ohm resistor.
UART channel A Request-to-Send (active low) or general purpose output. This out-
put must be asserted prior to using auto RTS flow control, see EFR[6], MCR[1],
and IER[6].
UART channel A Clear-to-Send (active low) or general purpose input. It can be
used for auto CTS flow control, see EFR[7], and IER[7]. This input should be con-
nected to VCC when not used.
UART channel A Data-Terminal-Ready (active low) or general purpose output. If it
is not used, leave it unconnected.
UART channel A Data-Set-Ready (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
UART channel A Carrier-Detect (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
UART channel A Ring-Indicator (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
4
D
ESCRIPTION
Table 3
Table 3
Table 3
Table 4
. If it is not used, leave it uncon-
. If it is not used, leave it uncon-
. If it is not used, leave it uncon-
. If it is not used, leave it uncon-
REV. 1.0.2