73s8009r-il Maxim Integrated Products, Inc., 73s8009r-il Datasheet - Page 14
![no-image](/images/no-image-200.jpg)
73s8009r-il
Manufacturer Part Number
73s8009r-il
Description
Low Cost Versatile Smart Card Interface
Manufacturer
Maxim Integrated Products, Inc.
Datasheet
1.73S8009R-IL.pdf
(23 pages)
73S8009R Data Sheet
3.2
Four separate digital inputs allow direct control of the card interface from the host as follows:
•
•
•
Other functions are controlled as follows:
•
•
•
•
3.3
The Teridian 73S8009R smart card interface IC incorporates a LDO voltage regulator. The voltage
output is controlled by the digital input sequence on CMDVCC# and CMDVCC%. This regulator is able to
provide either 1.8 V, 3 V or 5 V card voltages from the power supply applied on the VPC pin.
Digital circuitry is powered by the power supply applied on the VDD pin. V
range to interface with the system controller.
Three voltage supervisors constantly check the presence of the voltages V
deactivation sequence is forced upon a fault detected by any of these voltage supervisors.
The voltage regulator can provide a card current of 65 mA in compliance with EMV 4.1, and of at least
90 mA in compliance with ISO7816-3. The V
EMV standard.
3.4
The card power supply is internally provided by the LDO regulator. The signals CMDVCC# and
CMDVCC% control the turn-on, output voltage value, and turn-off of V
low, V
V
V
ignored (and vice versa).
At the assertion (low) of either or both CMDVCC#/CMDVCC% signals, V
When V
set high. Approximately 510 µs after the fall of CMDVCC#/CMDVCC% the circuit will check the see if V
is at or above the required minimum value (indicated by RDY=1) and if not, will begin an emergency
deactivation sequence. During the 510 µs time, over-temperature, card removal, or de-assertion of
CMDVCC#/CMDVCC% shall also initiate an emergency deactivation sequence.
14
CC
CC
Pin CS: Enables the system controller interface.
Pin CMDVCC# and/or CMDVCC%: When low, starts an activation sequence.
Pin RSTIN: Controls the card Reset signal (when enabled by the sequencer).
PWRDN places the 73S8009R in a low power mode and shuts down all functions.
The card clock is completely controlled by CLKIN.
Vcc output voltage valid is indicated on the RDY pin.
Interrupt output to the host: As long as the card is not activated, the OFF pin informs the host about
the card presence only (low = no card in the reader).
When CMDVCC is set low (Card activation sequence requested from the host), a low level on OFF
means a fault has been detected (e.g. card removal during card session, or voltage fault, or thermal /
over-current fault). This condition automatically initiates a deactivation sequence.
will ramp to 1.8 volts. These signals are edge triggered. If CMDVCC% is asserted low (to command
to be 5 V) and at a much later time (greater than 2 µs, typically), CMDVCC# is asserted low, it will be
CC
System Controller Interface
Power Supply and Voltage Supervision
Card Power Supply
CC
will ramp to the selected value or if both signals are asserted low (within 400 ns of each other),
rises to an acceptable value, and stays above that value for approximately 20 µs, RDY will be
CC
voltage supervisor threshold values are defined from the
CC
. When either signal is asserted
CC
DD
DD
will rise to the requested value.
, V
also defines the voltage
PC
and V
CC
DS_8009R_056
. A card
Rev. 1.3
CC