wm8802scft/v Wolfgang Knap, wm8802scft/v Datasheet - Page 36
wm8802scft/v
Manufacturer Part Number
wm8802scft/v
Description
Digital Audio Interface Transceiver
Manufacturer
Wolfgang Knap
Datasheet
1.WM8802SCFTV.pdf
(65 pages)
- Current page: 36 of 65
- Download datasheet (506Kb)
WM8802
GENERAL PURPOSE I/O (GPIO0, GPIO1, GPIO2, GPIO3, GPIOEN)
w
INITIAL SETTINGS
The modulation function and general-purpose parallel I/O’s share the same pins and therefore cannot
be used simultaneously. INT should be pulled down with a 10k
I/O’s. For the setting method, see page 10.
The general-purpose parallel I/O output function performs parallel conversion of the serial data input
from the micro-controller interface and outputs the resulting data from GPIO0 GPIO1, GPIO2 and
GPIO3. The input function saves the parallel data input to GPIO0, GPIO1, GPIO2, and GPIO3 to
internal registers and reads the contents of these registers with the micro-controller interface.
It is not possible to mix the 4 bit general-purpose I/O’s as inputs and outputs at the same time.
Switching between input and output is done using GPIOEN The general-purpose I/Os all become
input pins when GPIOEN is High and all output pins when GPIOEN is Low.
INPUT/OUTPUT SETTINGS
Data handling for general-purpose I/O is performed using the micro-controller interface and
write/read registers.
General-purpose I/O write settings (Micro-controller
General-purpose I/O read settings (General-purpose I/O input
1.
2.
3.
4.
1.
2.
3.
Set GPIOEN to Low to output data from general-purpose I/O’s.
Set the data to be output to CCB address 0xE8, command address 0x10 and input registers
DI12 to DI15.
During write operation, make sure "0" is written to modulation function setting registers DI8 to
DI11.
The data written to PI0 to PI3 is output from the general-purpose I/O’s.
Set GPIOEN to High to input data to general-purpose I/O’s.
The input data is saved to CCB address 0xEB and output registers DO0 to DO3.
Data can be sent to the micro-controller by reading GPO0 to GPO3.
Write register
Read register
resistor to use the general-purpose
General-purpose I/O output)
PP Rev 1.1 April 2004
Micro-controller)
Product Preview
36
Related parts for wm8802scft/v
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Connector Is Made Of Glassfbre Reinforced
Manufacturer:
Wolfgang Knap
Datasheet:
Part Number:
Description:
Panelmounted Receptacle Is Made Of Glassfbre Reinforced Plastic
Manufacturer:
Wolfgang Knap
Datasheet:
Part Number:
Description:
Cable-mounted Receptacles
Manufacturer:
Wolfgang Knap
Datasheet:
Part Number:
Description:
Back Shell With Pg-/m-thread
Manufacturer:
Wolfgang Knap
Datasheet:
Part Number:
Description:
Back Shell With Cable Gland
Manufacturer:
Wolfgang Knap
Datasheet:
Part Number:
Description:
90° Angled Adapters
Manufacturer:
Wolfgang Knap
Datasheet:
Part Number:
Description:
Pre-assembled Cables
Manufacturer:
Wolfgang Knap
Datasheet:
Part Number:
Description:
Connector Comprises A Diecast Zinc Shell
Manufacturer:
Wolfgang Knap
Datasheet:
Part Number:
Description:
Direct-to-air Peltierkühler Serie Da
Manufacturer:
Wolfgang Knap
Datasheet:
Part Number:
Description:
Low Power Clock Oscillator 32.768 Khz
Manufacturer:
Wolfgang Knap
Datasheet:
Part Number:
Description:
Connector Is Made Of Glassfbre Reinforced
Manufacturer:
Wolfgang Knap
Datasheet:
Part Number:
Description:
Panelmounted Receptacle Is Made Of Glassfbre Reinforced Plastic
Manufacturer:
Wolfgang Knap
Datasheet:
Part Number:
Description:
Cable-mounted Receptacles
Manufacturer:
Wolfgang Knap
Datasheet:
Part Number:
Description:
Back Shell With Pg-/m-thread
Manufacturer:
Wolfgang Knap
Datasheet:
Part Number:
Description:
Back Shell With Cable Gland
Manufacturer:
Wolfgang Knap
Datasheet: