adum1100 Analog Devices, Inc., adum1100 Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
adum1100
Manufacturer Part Number
adum1100
Description
Icoupler Digital Isolator
Manufacturer
Analog Devices, Inc.
Datasheet
1.ADUM1100.pdf
(20 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
adum1100AR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
adum1100AR-RL7
Manufacturer:
STM
Quantity:
3 706
Company:
Part Number:
adum1100ARZ
Manufacturer:
ADI
Quantity:
5 000
Part Number:
adum1100ARZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
adum1100ARZ-RL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
adum1100BR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
adum1100BR-RL7
Manufacturer:
TI
Quantity:
6 053
Part Number:
adum1100BRZ-RL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
ADuM1100
1
2
3
4
5
6
7
8
9
Output supply current values are with no output load present. See Figure 5 and Figure 6 for information on supply current variation with logic signal frequency. See
the Power Consumption section for guidance on calculating the input and output supply currents for a given data rate and output load.
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
t
rising edge of the V
Because the input thresholds of the ADuM1100 are at voltages other than the 50% level of typical input signals, the measured propagation delay and pulse width
distortion can be affected by slow input rise/fall times. See the Propagation Delay-Related Parameters section and Figure 14 through Figure 18 for information on the
impact of given input rise/fall times on these parameters.
Pulse width distortion change vs. temperature is the absolute value of the change in pulse width distortion for a 1°C change in operating temperature.
t
recommended operating conditions. t
temperature, supply voltages, and output load within the recommended operating conditions.
CM
that can be sustained while maintaining V
over which the common-mode is slewed.
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in signal data rate. See Figure 5 and Figure 6 for information on
supply current variation with logic signal frequency. See the Power Consumption section for guidance on calculating the input and output supply currents for a given
data rate and output load.
PHL
PSK1
H
is measured from the 50% level of the falling edge of the V
is the magnitude of the worst-case difference in t
is the maximum common-mode voltage slew rate that can be sustained while maintaining V
I
signal to the 50% level of the rising edge of the V
PSK2
is the magnitude of the worst-case difference in t
O
< 0.8 V. The common-mode voltage slew rates apply to both rising and falling edges. The transient magnitude is the range
PHL
and/or t
I
signal to the 50% level of the falling edge of the V
PLH
that is measured between units at the same operating temperature and output load within the
O
signal.
Rev. G | Page 4 of 20
PHL
and/or t
O
> 0.8 V
PLH
that is measured between units at the same operating
DD2
. CM
L
O
is the maximum common-mode voltage slew rate
signal. t
PLH
is measured from the 50% level of the