k4t1g084qa-zce6 Samsung Semiconductor, Inc., k4t1g084qa-zce6 Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
k4t1g084qa-zce6
Manufacturer Part Number
k4t1g084qa-zce6
Description
1gb A-die Ddr2 Sdram Specification
Manufacturer
Samsung Semiconductor, Inc.
Datasheet
1.K4T1G084QA-ZCE6.pdf
(28 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
K4T1G084QA-ZCE6
Manufacturer:
SAMSUNG
Quantity:
8 723
1G A-die DDR2 SDRAM
Input/Output Functional Description
In this data sheet, "differential DQS signals" refers to any of the following with A10 = 0 of EMRS(1)
(UDQS), (UDQS)
(RDQS), (RDQS)
(LDQS), (LDQS)
RAS, CAS, WE
DQS, (DQS)
BA0 - BA2
V
V
A0 - A13
Symbol
CK, CK
DD
SS
V
V
V
CKE
ODT
DM
DQ
NC
SSDL
CS
/V
/V
DDL
REF
DDQ
SSQ
"single-ended DQS signals" refers to any of the following with A10 = 1 of EMRS(1)
Input/Output
Input/Output
Supply
Supply
Supply
Supply
Supply
Type
Input
Input
Input
Input
Input
Input
Input
Input
x16 LDQS and UDQS
x4 DQS/DQS
x8 DQS/DQS
x8 DQS/DQS, RDQS/RDQS,
x16 LDQS/LDQS and UDQS/UDQS
x4 DQS
x8 DQS
x8 DQS, RDQS,
Clock: CK and CK are differential clock inputs. All address and control input signals are sampled on the crossing of
the positive edge of CK and negative edge of CK. Output (read) data is referenced to the crossings of CK and CK
(both directions of crossing).
Clock Enable: CKE HIGH activates, and CKE Low deactivates, internal clock signals and device input buffers and
output drivers. Taking CKE Low provides Precharge Power-Down and Self Refresh operation (all banks idle), or
Active Power-Down (row Active in any bank). CKE is synchronous for power down entry and exit, and for self
refresh entry. CKE is asynchronous for self refresh exit. After V
tialization swquence, it must be maintained for proper operation of the CKE receiver. For proper self-refresh entry
and exit, V
Input buffers, excluding CK, CK, ODT and CKE are disabled during power-down. Input buffers, excluding CKE, are
disabled during self refresh.
Chip Select: All commands are masked when CS is registered HIGH. CS provides for external Rank selection on
systems with multiple Ranks. CS is considered part of the command code.
On Die Termination: ODT (registered HIGH) enables termination resistance internal to the DDR2 SDRAM. When
enabled, ODT is only applied to each DQ, DQS, DQS, RDQS, RDQS, and DM signal for x4/x8 configurations. For
x16 configuration, ODT is applied to each DQ, UDQS/UDQS, LDQS/LDQS, UDM, and LDM signal. The ODT pin
will be ignored if the Extended Mode Register Set(EMRS) is programmed to disable ODT.
Command Inputs: RAS, CAS and WE (along with CS) define the command being entered.
Input Data Mask: DM is an input mask signal for write data. Input data is masked when DM is sampled HIGH coin-
cident with that input data during a Write access. DM is sampled on both edges of DQS. Although DM pins are input
only, the DM loading matches the DQ and DQS loading. For x8 device, the function of DM or RDQS/RDQS is
enabled by EMRS command.
Bank Address Inputs: BA0, BA1 and BA2 define to which bank an Active, Read, Write or Precharge command is
being applied. Bank address also determines if the mode register or extended mode register is to be accessed dur-
ing a MRS or EMRS cycle.
Address Inputs: Provided the row address for Active commands and the column address and Auto Precharge bit
for Read/Write commands to select one location out of the memory array in the respective bank. A10 is sampled
during a Precharge command to determine whether the Precharge applies to one bank (A10 LOW) or all banks
(A10 HIGH). If only one bank is to be precharged, the bank is selected by BA0, BA1 and BA2. The address inputs
also provide the op-code during Mode Register Set commands.
Data Input/ Output: Bi-directional data bus.
Data Strobe: Output with read data, input with write data. Edge-aligned with read data, centered in write data. For
the x16, LDQS corresponds to the data on DQ0-DQ7; UDQS corresponds to the data on DQ8-DQ15. For the x8, an
RDQS option using DM pin can be enabled via the EMRS(1) to simplify read timing. The data strobes DQS, LDQS,
UDQS, and RDQS may be used in single ended mode or paired with optional complementary signals DQS, LDQS,
UDQS, and RDQS to provide differential pair signaling to the system during both reads and writes. An EMRS(1)
control bit enables or disables all complementary data strobe signals.
No Connect: No internal electrical connection is present.
Power Supply: 1.8V +/- 0.1V, DQ Power Supply: 1.8V +/- 0.1V
Ground, DQ Ground
DLL Power Supply: 1.8V +/- 0.1V
DLL Ground
Reference voltage
REF
if EMRS(1) [A11] = 0
if EMRS(1) [A11] = 1
must be maintained to this input. CKE must be maintained high throughout read and write accesses.
if EMRS(1)[A11] = 0
Page 9 of 28
if EMRS(1)[A11] = 1
Function
REF
has become stable during the power on and ini-
DDR2 SDRAM
Rev. 1.1 Aug. 2005