k4t51043qc-zle7 Samsung Semiconductor, Inc., k4t51043qc-zle7 Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
k4t51043qc-zle7
Manufacturer Part Number
k4t51043qc-zle7
Description
512mb C-die Ddr2 Sdram
Manufacturer
Samsung Semiconductor, Inc.
Datasheet
1.K4T51043QC-ZLE7.pdf
(29 pages)
2.2 Input/Output Functional Description
512Mb C-die DDR2 SDRAM
(UDQS), (UDQS)
(RDQS), (RDQS)
(LDQS), (LDQS)
RAS, CAS, WE
DQS, (DQS)
BA0 - BA1
V
V
A0 - A13
Symbol
CK, CK
DD
SS
V
V
V
CKE
ODT
DM
DQ
NC
SSDL
CS
DDL
REF
/V
/V
DDQ
SSQ
Input/Output Data Input/ Output: Bi-directional data bus.
Input/Output
Supply
Supply
Supply
Supply
Supply
Type
Input
Input
Input
Input
Input
Input
Input
Input
Clock: CK and CK are differential clock inputs. All address and control input signals are sampled on the crossing of the positive edge of
CK and negative edge of CK. Output (read) data is referenced to the crossings of CK and CK (both directions of crossing).
Clock Enable: CKE HIGH activates, and CKE Low deactivates, internal clock signals and device input buffers and output drivers. Tak-
ing CKE Low provides Precharge Power-Down and Self Refresh operation (all banks idle), or Active Power-Down (row Active in any
bank). CKE is synchronous for power down entry and exit, and for self refresh entry. CKE is asynchronous for self refresh exit. After
V
receiver. For proper self-refresh entry and exit, V
and write accesses. Input buffers, excluding CK, CK, ODT and CKE are disabled during power-down. Input buffers, excluding CKE, are
disabled during self refresh.
Chip Select: All commands are masked when CS is registered HIGH. CS provides for external Rank selection on systems with multiple
Ranks. CS is considered part of the command code.
On Die Termination: ODT (registered HIGH) enables termination resistance internal to the DDR2 SDRAM. When enabled, ODT is only
applied to each DQ, DQS, DQS, RDQS, RDQS, and DM signal for x4/x8 configurations. For x16 configuration ODT is applied to each
DQ, UDQS/UDQS, LDQS/LDQS, UDM, and LDM signal. The ODT pin will be ignored if the Extended Mode Register (EMRS(1)) is pro-
grammed to disable ODT.
Command Inputs: RAS, CAS and WE (along with CS) define the command being entered.
Input Data Mask: DM is an input mask signal for write data. Input data is masked when DM is sampled HIGH coincident with that input
data during a Write access. DM is sampled on both edges of DQS. Although DM pins are input only, the DM loading matches the DQ
and DQS loading. For x8 device, the function of DM or RDQS/RDQS is enabled by EMRS command.
Bank Address Inputs: BA0 - BA1 define to which bank an Active, Read, Write or Precharge command is being applied (For 256Mb and
512Mb, BA2 is not applied). Bank address also determines if the mode register or extended mode register is to be accessed during a
MRS or EMRS cycle.
Address Inputs: Provided the row address for Active commands and the column address and Auto Precharge bit for Read/Write com-
mands to select one location out of the memory array in the respective bank. A10 is sampled during a Precharge command to determine
whether the Precharge applies to one bank (A10 LOW) or all banks (A10 HIGH). If only one bank is to be precharged, the bank is
selected by BA0, BA1. The address inputs also provide the op-code during Mode Register Set commands.
Data Strobe: output with read data, input with write data. Edge-aligned with read data, centered in write data. For the x16, LDQS corre-
sponds to the data on DQ0-DQ7; UDQS corresponds to the data on DQ8-DQ15. For the x8, an RDQS option using DM pin can be
enabled via the EMRS(1) to simplify read timing. The data strobes DQS, LDQS, UDQS, and RDQS may be used in single ended mode
or paired with optional complementary signals DQS, LDQS, UDQS, and RDQS to provide differential pair signaling to the system during
both reads and writes. An EMRS(1) control bit enables or disables all complementary data strobe signals.
In this data sheet, "differential DQS signals" refers to any of the following with A10 = 0 of EMRS(1)
"single-ended DQS signals" refers to any of the following with A10 = 1 of EMRS(1)
No Connect: No internal electrical connection is present.
Power Supply: 1.8V +/- 0.1V, DQ Power Supply: 1.8V +/- 0.1V
Ground, DQ Ground
DLL Power Supply: 1.8V +/- 0.1V
DLL Ground
Reference voltage
x16 LDQS and UDQS
x4 DQS
x8 DQS if EMRS(1)[A11] = 0
REF
x4 DQS/DQS
x8 DQS/DQS
x8 DQS/DQS, RDQS/RDQS,
x16 LDQS/LDQS and UDQS/UDQS
x8 DQS, RDQS, if EMRS(1)[A11] = 1
has become stable during the power on and initialization swquence, it must be maintained for proper operation of the CKE
if EMRS(1)[A11] = 0
if EMRS(1)[A11] = 1
Page 9 of 29
REF
must be maintained to this input. CKE must be maintained high throughout read
Function
DDR2 SDRAM
Rev. 1.4 Aug. 2005