MSC2323258A-XXBS4 OKI [OKI electronic componets], MSC2323258A-XXBS4 Datasheet
![no-image](/images/no-image-200.jpg)
MSC2323258A-XXBS4
Related parts for MSC2323258A-XXBS4
MSC2323258A-XXBS4 Summary of contents
Page 1
... DRAM MODULE : FAST PAGE MODE TYPE WITH EDO DESCRIPTION The Oki MSC2323258A-xxBS4/DS4 is a fully decoded 2,097,152-word ¥ 32-bit CMOS dynamic random access memory composed of two 16-Mb (1M ¥ 16) DRAMs in SOJ. The mounting of two DRAMs together with decoupling capacitors on a 72-pin glass epoxy SIMM Package supports any application where high density and large capacity of storage memory are required ...
Page 2
... MSC2323258A-xxBS4/DS4 PIN CONFIGURATION MSC2323258A-xxBS4/DS4 3.38 Typ. f 3.18 19.0 ±0.2 Typ. Typ. 10.16 1 6.35 2.03 Typ. 1.27 ±0.2 6.35 Typ. *1 The common size difference of the board width 12 its height is specified as ±0.2. The value above 12 specified as ±0.5. Pin No. Pin Name Pin No. Pin Name DQ0 17 3 DQ16 18 4 DQ1 ...
Page 3
... DQ1 DQ1 DQ1 DQ2 DQ2 DQ2 DQ15 DQ15 DQ15 DQ0 DQ16 DQ0 DQ1 DQ17 DQ1 DQ2 DQ18 DQ2 DQ15 DQ31 DQ15 MSC2323258A-xxBS4/DS4 RAS RAS1 LCAS UCAS RAS RAS3 LCAS UCAS ...
Page 4
... MSC2323258A-xxBS4/DS4 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings Parameter Voltage on Any Pin Relative Voltage V Supply Relative Short Circuit Output Current Power Dissipation Operating Temperature Storage Temperature Note: Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to the conditions as detailed in the operational sections of this data sheet ...
Page 5
... Min. — — 4 –0 — 450 IH = Min. — 450 = Min — 450 = Min. for output open condition. CC MSC2323258A-xxBS4/DS4 ( ±10 0°C to 70°C) CC MSC2323258A -70BS4/DS4 Unit Note 1 Min. Max. –40 40 µA –20 20 µ — ...
Page 6
... MSC2323258A-xxBS4/DS4 AC Characteristics (1/2) Parameter Random Read or Write Cycle Time Fast Page Mode Cycle Time Access Time from RAS Access Time from CAS Access Time from Column Address Access Time from CAS Precharge Output Low Impedance Time from CAS Output Hold Time from CAS Low ...
Page 7
... Data-in Set-up Time Data-in Hold Time Data-in Hold Time from RAS CAS Active Delay Time from RAS Precharge RAS to CAS Set-up Time (CAS before RAS) RAS to CAS Hold Time (CAS before RAS) MSC2323258A-xxBS4/DS4 ( ±10 0°C to 70°C) CC MSC2323258A MSC2323258A ...
Page 8
... MSC2323258A-xxBS4/DS4 Notes start-up delay of 200 s is required after power-up, followed by a minimum of eight initialization cycles (RAS-only refresh or CAS before RAS refresh) before proper device operation is achieved. 2. The AC characteristics assume (Min.) and V IH Transition times (t 4. This parameter is measured with a load circuit equivalent to 2 TTL loads and 100 pF. ...