SPB-24 GAMEWELL-FCI [Gamewell-FCI by Honeywell], SPB-24 Datasheet

no-image

SPB-24

Manufacturer Part Number
SPB-24
Description
Complete system includes emitter and receiver
Manufacturer
GAMEWELL-FCI [Gamewell-FCI by Honeywell]
Datasheet
line type of device designed to detect black, gray or white
smoke over large, elongated areas. The system consists of an
emitter and receiver. The emitter projects a near infrared
pulsed beam to a receiver which may be located from 10 up to
l00 meters (32.8 to 328 feet) from the emitter. Spacing be-
tween units can be as much as 45 feet on centers.
tween blockage and smoke from fires make the SPB well
suited for use in atriums, gymnasiums, theaters, museums,
factories, tunnels, churches, cathedrals, anechoic chambers
and high air velocity areas.
for obscurations of 25%, 50% and 70%. These settings are
dependent upon the monitoring distance and ceiling height.
Should the smoke from a fire cause a decrease in the signal
strength of a magnitude that exceeds the programmed
obscuration setting, an alarm signal is generated. An inter-
ruption of 90% of the beam within a short period of time will
create a trouble condition. Thus the unit can readily distin-
guish between a high smoke level and a sudden blockage or
emitter failure.
the transmitter and receiver heads facing each other from be-
hind windows outside the explosive areas. The beam can be
projected up to 30 meters (100 feet) in such applications.
Form “B” trouble contacts. This detector may be used with
any UL listed 24 VDC control panel having the proper cur-
rent capacity.
cally makes periodic adjustments to the system to compen-
sate for normal ambient changes that cause contamination of
the lenses and for aging components. Since such a change
with time appears as a slow change in the beam signal, the
microcomputer compensates in such a manner that the signal
moves closer to the reference data at a rate of approximately
1% per hour. When this compensating capability reaches a
limit, the microprocessor automatically generates a trouble
signal.
The FCI Model SPB-24 projected beam smoke detector is a
The length of protected path and ability to distinguish be-
The detector has three field adjustable sensitivity settings
Explosive atmospheres may also be protected by locating
Outputs from the receiver are Form “A” alarm contacts and
The receiver contains a microprocessor which automati-
by Gamewell-FCI for their use. Specifications subject to change without notice.
U.L. (STD 268)
Factory Mutual
Specifications are provided for information only, are not intended to be used for installation purposes, and are believed to be accurate. However, no responsibility is assumed
DESCRIPTION
APPROVALS
12 Clintonville Road, Northford, CT 06472 - Tel: (203) 484-7161 - Fax: (203) 484-7118
S1383
1Y0A5.AY
www.gamewell-fci.com
GAMEWELL-FCI
· Use with any FCI or Other U.L. Listed
· Operation Unaffected by Air Velocity
· Three Field Adjustable Sensitivity
· Form “A” Alarm Contacts
· Form “B” Trouble Contacts
· Four-wire Configuration
· Low Supervisory Current
· Calibrated Filters available
© 2006 All Rights Reserved.
Control
Settings: 25%, 50% and 70%
to Verify Sensitivity
PROJECTED BEAM
SMOKE DETECTOR
FEATURES
SPB-24
9020-0382 Rev. E
1 of 2

Related parts for SPB-24

SPB-24 Summary of contents

Page 1

... DESCRIPTION The FCI Model SPB-24 projected beam smoke detector is a line type of device designed to detect black, gray or white smoke over large, elongated areas. The system consists of an emitter and receiver. The emitter projects a near infrared pulsed beam to a receiver which may be located from l00 meters (32 ...

Page 2

... VDC (42 V peak) 250 uA (average) .020 122 F (non-condensing) 3.4" 4.0" 5.7" H ORDERING INFORMATION Model Description SPB-24 Complete system includes emitter and receiver Test filter set RELAY ENERGIZED LED WHITE 0 V (-) BLUE GRAY +24 V YELLOW RED +12 V ...

Related keywords