CC2530F128 APLUS [Aplus Intergrated Circuits], CC2530F128 Datasheet - Page 6

• Manufacturer Part Number: CC2530F128
• Description: A True System-on-Chip Solution for 2.4-GHz IEEE 802.15.4 and ZigBee Applications
• Manufacturer: APLUS [Aplus Intergrated Circuits]

CC2530F32, CC2530F64, CC2530F128, CC2530F256
SWRS081A – APRIL 2009 – REVISED APRIL 2009
RF RECEIVE SECTION (continued)
Measured on Texas Instruments CC2530 EM reference design with T
otherwise noted.
Boldface limits apply over the entire operating range, T
2507 MHz.
(1) Difference between center frequency of the received RF signal and local oscillator frequency.
(2) Difference between incoming symbol rate and the internally generated symbol rate
RF TRANSMIT SECTION
Measured on Texas Instruments CC2530 EM reference design with T
otherwise noted.
Boldface limits apply over the entire operating range, T
MHz.
(1) Texas Instruments CC2530 EM reference design is suitable for systems targeting compliance with EN 300 328, EN 300 440, FCC
(2) Margins for passing conducted requirements at the third harmonic can be improved by using a simple band-pass filter connected
(3) Margins for passing FCC requirements at 2483.5 MHz and above when transmitting at 2480 MHz can be improved by using a lower
6
Spurious emission. Only largest spurious
emission stated within each band.
30 MHz–1000 MHz
1 GHz–12.75 GHz
Frequency error tolerance
Symbol rate error tolerance
Nominal output power
Programmable output power
range
Spurious emissions
Measured conducted
according to stated
regulations. Only largest
spurious emission stated
within each band.
Error vector magnitude (EVM)
Optimum load impedance
CFR47 Part 15 and ARIB STD-T-66.
between matching network and RF connector (1.8 pF in parallel with 1.6 nH); this filter must be connected to a good RF ground.
output-power setting or having less than 100% duty cycle.
PARAMETER
Submit Documentation Feedback
PARAMETER
(1)
(2)
Product Folder Link(s):
Delivered to a single-ended 50-Ω load through a balun using
maximum-recommended output-power setting
[1] requires minimum –3 dBm
Max recommended output power setting
25 MHz–1000 MHz (outside restricted bands)
25 MHz–2400 MHz (within FCC restricted bands)
25 MHz–1000 MHz (within ETSI restricted bands)
1800–1900 MHz (ETSI restricted band)
5150–5300 MHz (ETSI restricted band)
At 2 × f
At 2 × f
1 GHz–12.75 GHz (outside restricted bands)
At 2483.5 MHz and above (FCC restricted band)
Measured as defined by [1] using maximum-recommended
output-power setting
[1] requires maximum 35%.
Differential impedance as seen from the RF port (RF_P and RF_N)
towards the antenna
f
c
= 2480 MHz
c
c
and 3 × f
and 3 × f
Conducted measurement with a 50-Ω single-ended load.
Suitable for systems targeting compliance with EN 300 328,
EN 300 440, FCC CFR47 Part 15 and ARIB STD-T-66.
[1] requires minimum 80 ppm
[1] requires minimum 80 ppm
..........................................................................................................................................................
(3)
c
c
(FCC restricted band)
(ETSI EN 300-440 and EN 300-328)
CC2530F32 CC2530F64 CC2530F128 CC2530F256
TEST CONDITIONS
A
A
= –40°C to 125°C, VDD = 2 V to 3.6 V, and f
= –40°C to 125°C, VDD = 2 V to 3.6 V and f
TEST CONDITIONS
(1)
A
A
= 25°C, VDD = 3 V, and f
= 25°C, VDD = 3 V and f
(2)
Copyright © 2009, Texas Instruments Incorporated
MIN
–8
c
0
c
= 2440 MHz, unless
= 2440 MHz, unless
MIN
69 + j29
c
c
= 2394 MHz to 2507
±1000
= 2394 MHz to
TYP
–60
–60
–60
–57
–55
–42
–31
–53
–42
±150
2%
4.5
TYP MAX
32
–80
–57
<
MAX
10
8
www.ti.com
UNIT
UNIT
dBm
ppm
ppm
dBm
dBm
dB
Ω