S3031BH0 AMCC [Applied Micro Circuits Corporation], S3031BH0 Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
S3031BH0
Manufacturer Part Number
S3031BH0
Description
E4/STM-1/OC-3 ATM TRANSCEIVER
Manufacturer
AMCC [Applied Micro Circuits Corporation]
Datasheet
1.S3031BH0.pdf
(26 pages)
S3031B RECEIVER OPERATION
The S3031B transceiver chip provides the first stage of
the digital process of a receive SONET STS-3 or ITU-
T E4 serial bit stream. A Coded Mark Inversion (CMI)
decoder can be enabled for decoding STS-3 electrical
and E4 signal. The recovered and decoded signal is
output as both retimed bit-serial 155.52 or 139.264
Mbps NRZ data and as a 38.88 or 34.816 Mbyte/s 4-bit
nibble parallel outputs.
Clock recovery is performed on the incoming scrambled
NRZ or CMI-coded data stream. A reference clock is
required for phase locked loop start-up and proper
operation under loss of signal conditions. An integral
prescaler and phase locked loop circuit is used to
multiply this reference frequency to the nominal bit rate.
Clock Recovery
The clock recovery function, as shown in the block
diagram in Figure 9, generates a clock that is fre-
quency matched to the incoming data baud rate at
the RSDATIP/N differential inputs. The clock is phase
aligned by a PLL so that it samples the data in the
center of the data eye pattern.
The phase relationship between the edge transitions
of the data and those of the generated clock are
compared by a phase/frequency discriminator. Out-
put pulses from the discriminator indicate the required
direction of phase corrections. These pulses are
smoothed by an integral loop filter. The output of the
loop filter controls the frequency of the Voltage Con-
trolled Oscillator (VCO), which generates the recov-
ered clock. Frequency stability without incoming data
is guaranteed by an alternate reference input
(REFCLK) to which the PLL locks when data is lost.
When the Test Clock Enable (TSTCLKEN) input is
set high, the clock recovery block is disabled. The
Test Clock (TESTCLK) is used as the bit rate clock
input in place of the recovered clock. This feature is
used for functional testing of the device.
The loop filter transfer function is optimized to enable
the PLL to track the jitter, yet tolerate the minimum
transition density expected in a received SONET or
E4 data signal. This transfer function yields a typical
capture time of 16 s for random incoming NRZ data.
The total loop dynamics of the clock recovery PLL yield
a jitter tolerance which exceeds the minimum tolerance
proposed for OC-3/STM-1/E4 equipment by the Bellcore
and ITU-T documents, shown in Figure 12.
August 19, 1999 / Revision D
E4/STM-1/OC-3 ATM TRANSCEIVER
Optical and Electrical Interfaces
The digital data inputs (RSDATIP/N) are the PECL
inputs from an optical to electrical converter, as shown
in Figure 16. The data input for the coaxial interface is
ANDATIN, which is the serial data input from the equal-
izer circuit and should be connected as shown in Figure
19. The EQUALSEL input is used to select either
RSDATIP/N or ANDATIN.
CMI Decoding
The CMI decoder block on the S3031B accepts serial
data from the TSDATIP/N input at the rate of 139.264 or
155.52 Mbps. The incoming CMI data, which has tran-
sitions that represent this data rate (the clock associ-
ated with this data would be running at twice this rate),
is then decoded from CMI to NRZ format.
Loss of Signal
The clock recovery circuit monitors the incoming data
stream for loss of signal. If the incoming encoded data
stream has had no transitions continuously for 100 to
200 recovered clock cycles, loss of signal is declared
and the PLL will switch from locking onto the incoming
data to locking onto the reference clock per the require-
ments of G.775. Alternatively, the loss-of signal (LOSIN)
input can force a loss-of-signal condition. This signal is
compared internally against the LOSREF input refer-
ence voltage. This input can be set to meet the condi-
tions shown in Figure 10. If the zero to peak signal level
drops below the LOSREF/20 voltage level for more than
100 to 200 bit intervals, a loss of signal condition will be
indicated on the LOSOUT pin and the PLL will change
its reference from the serial data stream to the reference
clock. When the peak input voltage is greater than
LOSREF/10, the loss of signal condition will be
deasserted and the PLL will recover the clock from the
serial data inputs.
In clock recovery mode, the receiver PLL also moni-
tors the reference clock with respect to the VCO. If the
VCO drifts away from the local reference clock by
more than 1000 ppm the PLL will re-lock to the refer-
ence clock and the LOSOUT will be set to the active
low condition.
The LOSOUT will return to the High or inactive state
and the PLL will again lock to the data if the serial data
contains sufficient transition density (less than 100 to
200 bit times between rising edges), and the serial
clock is within 250 ppm of the reference clock deter-
mined frequency.
S3031B
7