icx267al Sony Electronics, icx267al Datasheet
icx267al
Related parts for icx267al
icx267al Summary of contents
Page 1
... Diagonal 8mm (Type 1/2) Progressive Scan CCD Image Sensor with Square Pixel for B/W Cameras Description The ICX267AL is a diagonal 8mm (Type 1/2) interline CCD solid-state image sensor with a square pixel array and 1.45M effective pixels. Progressive scan allows all pixels' signals to be output independently. Also, the adoption of high frame rate readout mode supports 30 frames per second ...
Page 2
... The terms and conditions in the Sony additional specifications, which will be made available to you when you order the Products, shall also be applicable to your use of the Products as well as to this specifications book. You should review those terms and conditions when you consider purchasing and/or using the Products. – 2 – ICX267AL ...
Page 3
... SUB φRG 19 Hφ Hφ 2 – 3 – ICX267AL Note) : Photo sensor Description Supply voltage GND Substrate clock Substrate bias ∗ 1 Protective transistor bias Reset gate clock Horizontal register transfer clock Horizontal register transfer clock ...
Page 4
... GND SUB – GND 3 , GND – – 4 – ICX267AL Ratings Unit Remarks –40 to +10 V –50 to +15 V –50 to +0.3 V –40 to +0.3 V – ...
Page 5
... VH3 , –8.4 –8.0 –7.6 VL3 , 7.6 8.0 8 0.1 VL3 0.9 1.3 1.0 0.9 4.75 5.0 5.25 –0.05 0 0.05 3.0 3.3 5.5 0.4 RGLL 0.5 RGLm 22.15 23.0 23.85 – 5 – ICX267AL Unit Remarks V Unit Remarks mA Waveform Unit Remarks diagram VH02A VL1 VL3 High-level coupling V 2 High-level coupling V 2 Low-level coupling ...
Page 6
... H Rφ RG Vφ Rφ H Hφ 1 V2A Cφ V2A3 Cφ Cφ V13 R 3 Vφ 3 Horizontal transfer clock equivalent circuit Cφ RG – 6 – ICX267AL Min. Typ. Max. Unit Remarks 2200 pF 3300 pF 3300 pF 3300 pF 1200 pF 1200 pF 2200 100 ...
Page 7
... VH3 V VHH V VHL V VLH VLL Vφ VH02A V1 VH1 + V )/2 Vφ VL01 VL03 V2A VH02A Vφ VL03 V2B VH02B Vφ VH3 – 7 – ICX267AL 0V and Vφ – V VL01 – V VL2A – V VL2B – V VL03 ...
Page 8
... Hφ RGH twl Point A is the minimum value of the coupling waveform during the period from RGLL and V . RGLH RGLL . RGLm Vφ SUB tr twh tf – 8 – ICX267AL V CR twl V HL and Hφ waveforms two RGL φM φM 2 ...
Page 9
... Hφ rising side of the Hφ two Unit Min. Typ. Max. , Hφ 600 700 800 Wave Length [nm] – 9 – ICX267AL tf Unit Remarks During 0.5 µs readout ∗ 450 ns 7.5 5 7.5 ns ∗ 2 7.5 5 7.5 0.01 µs 0. When draining µ ...
Page 10
... H 8 1040 (V) 8 Signal output [ ∗ B] S/H – 10 – ICX267AL (Ta = 25°C) Remarks 1 1/30s accumulation Progressive scan 2 readout mode High frame rate 60°C readout mode High frame rate 2 readout two pixels addition ∗ 1 Progressive scan readout, high frame rate readout two ...
Page 11
... High frame rate readout mode 9 (V2A) 8 (V2B) 7 (V2B) 6 (V2A) 5 (V2A) 4 (V2B) 3 (V2B) 2 (V2A) 1 (V2A) V OUT – 11 – ICX267AL High frame rate readout two pixels addition mode 9 (V2A) 8 (V2B) 7 (V2B) 6 (V2A) 5 (V2A) 4 (V2B) 3 (V2B) 2 (V2A) 1 (V2A) V OUT ...
Page 12
... Then measure the maximum (Vrmax [mV]) and minimum (Vrmin [mV]) values of the signal output and substitute the values into the following formula (Vrmax – Vrmin)/150 × 100 [%] 2 , color temperature of 3200K halogen source subject. 1 [dB] (1/10V method conversion value) 10 – 12 – ICX267AL ...
Page 13
... Adjust the signal output value generated by strobe light to 150mV. After setting the strobe light so that it strobes with the following timing, measure the residual signal (Vlag). Substitute the value into the following formula. Lag = (Vlag/150) × 100 [%] VD V2A Strobe light timing Output Light signal output 150mV Vlag (lag) – 13 – ICX267AL ...
Page 14
... ICX267AL ...
Page 15
... ICX267AL ...
Page 16
... ICX267AL ...
Page 17
... ICX267AL ...
Page 18
... ICX267AL ...
Page 19
... ICX267AL ...
Page 20
... ICX267AL ...
Page 21
... ICX267AL ...
Page 22
... ICX267AL ...
Page 23
... ICX267AL ...
Page 24
... If a load is applied to the entire surface by a hard component, bending stress may be generated and the package may fracture, etc., depending on the flatness of the bottom of the package. Therefore, for installation, use either an elastic load, such as a spring plate adhesive. 50N Torsional strength – 24 – ICX267AL 1.2Nm ...
Page 25
... Exposure to high temperature or humidity will affect the characteristics. Accordingly avoid storage or usage in such conditions. c) The brown stain may be seen on the bottom or side of the package. But this does not affect the CCD characteristics. – 25 – ICX267AL ...
Page 26
... ICX267AL Sony Corporation ...