ch7013b ETC-unknow, ch7013b Datasheet - Page 3

• Manufacturer Part Number: ch7013b
• Description: Digital Pc To Tv Encoder
• Manufacturer: ETC-unknow

CHRONTEL
3.2 Pin Descriptions
201-0000-069
Table 1. Pin Descriptions
17-14, 11-9,
7-6, 4-1,
48-Pin
LQFP
48-46
41
43
45
44
39
35
36
27
24
23
In/Out
In/Out
Type
Rev. 1.2, 9/1/2004
Out
Out
Out
Out
In
In
In
In
In
Symbol
D15-D0
XO/FIN
P-OUT
RSET
XCLK
BCO
C/G
Y/R
XI
V
H
Digital Pixel Inputs
These pins accept digital pixel data streams with either 8, 12, or 16-bit multiplexed
or 16-bit non-multiplexed formats, determined by the input mode setting (see
Registers and Programming section). Inputs D0 - D7 are used when operating in 8-
bit multiplexed mode. Inputs D0 - D11 are used when operating in 12-bit mode.
Inputs D0 - D15 are used when operating in 16-bit mode. The data structure and
timing sequence for each mode is described in the section on Digital Input Port.
Pixel Clock Output
The CH7013B, operating in master mode, provides a pixel data clocking signal to
the VGA controller. This pin provides the pixel clock output signal (adjustable as X,
2X or 3X) to the VGA controller (see the section on Digital Video Interface and
Registers and Programming for more details). The capacitive loading on this pin
should be kept to a minimum.
Pixel Clock Input
To operate in a pure master mode, the P-OUT signal should be connected to the
XCLK input pin. To operate in a pseudo-master mode, the P-OUT clock is used as
a reference frequency, and a signal locked to this output (at 1X, 1/2X, or 1/3X the
P-OUT frequency) is input to the XCLK pin. To operate in slave mode, the
CH7013B accepts an external pixel clock input at this pin. The capacitive loading
on this pin should be kept to a minimum.
Vertical Sync Input/Output
This pin accepts the vertical sync signal from the VGA controller, or outputs a
vertical sync to the VGA controller. The capacitive loading on this pin should kept
to a minimum.
Horizontal Sync Input/Output
This pin accepts the horizontal sync from the VGA controller, or outputs a
horizontal sync to the VGA controller. The capacitive loading on this pin should be
kept to a minimum.
Buffered Clock Output
This pin provides a buffered output of the 14.31818 MHz crystal input frequency for
other devices and remains active at all times (including power-down). The output
can also be selected to be other frequencies (see Registers and Programming).
Crystal Input
A parallel resonance 14.31818 MHz (± 50 ppm) crystal should be attached
between XI and XO/FIN. However, if an external CMOS clock is attached to
XO/FIN, XI should be connected to ground.
Crystal Output or External Fref
A 14.31818 MHz (± 50 ppm) crystal may be attached between XO/FIN and XI. An
external CMOS compatible clock can be connected to XO/FIN as an alternative.
Reference Resistor
A 300 : resistor with short and wide traces should be attached between RSET and
ground. No other connections should be made to this pin.
Luminance Output
A 75 : termination resistor with short traces should be attached between Y and
ground for optimum performance. In normal operating modes other than SCART,
this pin outputs the luma video signal. In SCART mode, this pin outputs the red
signal.
Chrominance Output
A 75 : termination resistor with short traces should be attached between C and
ground for optimum performance. In normal operating modes other than SCART,
this pin outputs the chroma video signal. In SCART mode, this pin outputs the
green signal.
Description
CH7013B
3