us1260 ETC-unknow, us1260 Datasheet - Page 4

• Manufacturer Part Number: us1260
• Description: Dual Dropout Positive Adjustable Regulator
• Manufacturer: ETC-unknow

US1260
APPLICATION INFORMATION
APPLICATION INFORMATION
Introduction
The US1260 is a dual adjustable Low Dropout (LDO)
regulator packaged in a 7 pin TO220 which can easily
be programmed with the addition of two external resis-
tors to any voltages within the range of 1.20 to 5.5 V.
This voltage regulator is designed specifically for appli-
cations that require two separate regulators such as the
Intel PII processors requiring 1.5V and 2.5 V supplies,
eliminating the need for a second regulator which
results in lower overall system cost. When Vctrl pin
is connected to a supply which is at least 1V higher
than Vin, the dropout voltage improves by 30% which
makes it ideal for applications requiring less than the
standard 1.3V dropout given in the LDO products such
as US10XX series. The US1260 also provides an accu-
rate 1.20V voltage reference common to both regulators
for programming each output voltage. Other features of
the device include; fast response to sudden load current
changes, such as GTL+ termination application for
Pentium II
also includes thermal shutdown protection to protect the
device if an overload condition occurs.
Output Voltage Setting
The US1260 can be programmed to any voltages in the
range of 1.20V to 5.5V with the addition of R1 and R2
external resistors according to the following formula:
Figure 2 - Typical application of the US1260 for
3-4
Vctrl
Vin
I
R
V
Wehre :
B
1
OUT
=
& R as shown
0 02
programming the output voltage.
.
(Only one output is shown here)
2
family of microprocessors. The US1260
V
uA Typical
REF
V
Vin
Vctrl
REF
1
= .
US1260
120
R
R
Gnd
2
1
in figure
V Typically
R
Vout
2
Vfb
I
B
2
Vref
Ib
R2
R1
1260app2-1.0
Vout
The US1260 keeps a constant 1.20V between the Vfb
pin and ground pin. By placing a resistor R1 across these
two pins a constant current flows through R1, adding to
the
age equal to the (1.2/R1)*R2 +
to the 1.20V to set the output voltage as shown in the
above equation. Since the input bias current of the am-
plifier (
error to the output voltage and for most applications can
be ignored. For example, in a typical 1.5V
GTL+application if R1=10.2k and R2=2.55k the error
due to the Iadj is only 0.05mV which is less than 0.004%
of the nominal set point. The effective input imped-
ance seen by the feedback pins (R
ways be higher than 1.8k
tor to start up properly.
Load Regulation
Since the US1260 does not provide a separate ground
pin for the reference voltage, it is not possible to provide
true remote sensing of the output voltage at the load.
Figure 3 shows that the best load regulation is achieved
when the bottom side of R1 resistor is connected di-
rectly to the ground pin of US1260 (preferably to the tab
of the device) and the top side of R2 resistor is con-
nected to the load. In fact , if R1 is connected to the load
side, the effective resistance between the regulator and
the load is gained up by the factor of (1+R2/R1) ,or the
effective resistance will be ,Rp(eff)=Rp*(1+R2/R1).It is
important to note that for high current applications, this
can represent a significant percentage of the overall load
regulation and one must keep the path from the regula-
tor to the load as short as possible to minimize this
effect.
Figure 3 - Schematic showing connection for best load
Vctrl
I
Vin
FB
regulation. (Only one output is shown here)
I
current and into the R2 resistor producing a volt-
FB
) is only 0.02uA typically , it adds a very small
Vin
Vctrl
US1260
Gnd
Vout
Vfb
PARASITIC LINE
RESISTANCE
I
in order for the regula-
FB
Rp
* R2 which will be added
R2
R1
1
II R
1260app3-1.1
2
) must al-
Rev. 1.9
3/22/99
R L