DG401/883 INTERSIL [Intersil Corporation], DG401/883 Datasheet
DG401/883
Related parts for DG401/883
DG401/883 Summary of contents
Page 1
... The ON resistance variation with ana- log signals is quite low over a 15V analog input range. The three different devices provide the equivalent of two SPST (DG401/883), two SPDT (DG403/883) or two DPST (DG405/883) relay switch contacts with CMOS or TTL level activation. The pinout is similar, permitting a standard layout to be used, choosing the switch function as needed ...
Page 2
... DG401/883, DG403/883, DG405/883 Functional Diagrams DG401/883 GND V- Schematic Diagram GND V- Truth Table LOGIC 0 1 NOTE: Logic “0” 0.8V. Logic “1” 2.4V. DG403/883 ...
Page 3
... Specifications DG401/883, DG403/883, DG405/883 Absolute Maximum Ratings +44.0V GND 25V (GND - 0.3V) to (VC+) +0.3V L Digital Inputs (Note 1 (V-) - 30mA Continuous (Any Terminal) Current, (Note 1) Peak Current (Note 1) (Pulsed 1ms, 10% Duty Cycle) Storage Temperature Range (A Suffi -65 Lead Temperature (Soldering 10s +300 CAUTION: Stresses above those listed in “ ...
Page 4
... Specifications DG401/883, DG403/883, DG405/883 TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested +15V -15V PARAMETERS SYMBOL Turn On Time Turn Off Time t R OFF Break-Before-Make Time Delay (DG403 Only) NOTE: 1. Signals exceeding will be clamped by internal diodes. Limit forward diode current to maximum current ratings. ...
Page 5
... METALLIZATION: Type Å Å Thickness: 12k 1k GLASSIVATION: Type: Nitride Å Å Thickness WORST CASE CURRENT DENSITY 1 A/cm Metallization Mask Layout DG401/883 DG401/883 S1 S2 4-5 IN1 V- GND IN2 512046 Spec Number ...
Page 6
Die Characteristics DIE DIMENSIONS: 2150 m x 1720 m x 485 25 m METALLIZATION: Type Å Å Thickness: 12k 1k GLASSIVATION: Type: Nitride Å Å Thickness WORST CASE CURRENT DENSITY 1 ...
Page 7
... For load conditions, see Specifications. C and stray capacitance) FIGURE 1. SWITCHING TIME 10V 10V LOGIC INPUT 0 (includes fixture and stray capacitance) L FIGURE 2. BREAK-BEFORE-MAKE DG401/883, DG403/883, DG405/883 ...
Page 8
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com DG401/883, DG403/883, DG405/883 F16.3 MIL-STD-1835 GDIP1-T16 (D-2, CONFIGURATION A) ...
Page 9
DESIGN INFORMATION The information contained in this section has been developed through characterization by Intersil Corporation and is for use as application and design information only. No guarantee is implied. Typical Performance Curves 15V V- = -15V ...
Page 10
DESIGN INFORMATION The information contained in this section has been developed through characterization by Intersil Corporation and is for use as application and design information only. No guarantee is implied. Typical Performance Curves 0.0 -0.5 -1.0 -1 15V, ...
Page 11
DESIGN INFORMATION The information contained in this section has been developed through characterization by Intersil Corporation and is for use as application and design information only. No guarantee is implied. Typical Performance Curves NOT MEASURABLE ...
Page 12
DESIGN INFORMATION The information contained in this section has been developed through characterization by Intersil Corporation and is for use as application and design information only. No guarantee is implied. Typical Performance Curves 160 V+ = 15V V- = -15V ...