UFL-2LP-04-A ETC1 [List of Unclassifed Manufacturers], UFL-2LP-04-A Datasheet - Page 2

• Manufacturer Part Number: UFL-2LP-04-A
• Description: SMT Ultra-Miniature Coaxial Connectors-Mating Heights Owing to the Lowest Profile and the Lightest
• Manufacturer: ETC1 [List of Unclassifed Manufacturers]

2
*V.S.W.R. Measurement System
The above V.S.W.R. standard values were measured using the measurement system of the diagram below.
1. Contact resistance
2. Insulation resistance
3. Withstand voltage
4. V.S.W.R.*
5. Female contact holding force
6. Repetitive operation
7. Vibration
8. Shock
9. Humidity resistance
9.
10. Temperature cycle
11. Salt spray test
Materials
(Steady state)
Product Specifications
Ratings
Female center contact
Male center contact
Insulator
Item
Shell
Part
Nominal characteristic impedance
Rated frequency
Rated voltage
Center: 20 m
Outside: 10 m
500 M
No line or insulation breakdown
Dia.0.81Cable
Dia.1.13Cable
Dia.1.32Cable
0.15 N min.
Contact resistance
No momentary disconnections of 1 µs min.
No damage, cracks, or parts looseness min.
No momentary disconnections of 1 µs min.
No damage, cracks, or parts looseness
No damage, cracks, or parts looseness
Insulation resistance 100 M
Insulation resistance 500 M
No damage, cracks, or parts looseness
Contact resistance 25 m
No excessive corrosion
ø
Receptacle
min.
Plug
ø
ø
max.
max.
Phosphor bronze
Phosphor bronze
15 m
25 m
15 m
Specification
1.3 max.
Material
Brass
ø
ø
ø
ø
max. (Outside)
max. (Center)
max. (Outside)
max. (Center)
60 V AC (rms)
ø
ø
DC to 6 GHz
min.(High temperature)
min.(Pry)
50
NOTE 1: Cable type connectors were measured with SMA conversion adapters
NOTE 2: Board type connectors were mounted to a 50
ø
1.35
1.4
1.5
PBT
LCP
attached to both ends of the harness product of a suitable 100cm cable.
measurements were conducted with SMA conversion adapters attached.
Operating temperature range
Operating humidity
Measured at 10 mA max.
Measured at 100 V DC
200 V AC for 1 minute
DC to 3 GHz
3 to 6 GHz
Measured with a Ø 0.475 pin gauge
30 cycles of insertion and disengagement
Frequency of 10 to 100 Hz, single amplitude of 1.5 mm,
acceleration of 59 m/s
Acceleration of 735 m/s
waveform, for 6 cycles in the direction of each of the 3 axes
Temperature of 40˚C, humidity of 95%,
let stand for 96 hours
Temperature: +40˚C
Time:
Cycles: 5
48 hours continuous exposure to 5% salt water
Silver plating
Gold plating
Gold plating
Finish
Beige
Black
30 min.
2
, for 5 cyles in the direction of each of the 3 axes
/
/
5 to 35˚C
Within 5 min.
Conditions
2
, 11 ms duration, sine half-wave
-40˚C to +90˚C
/
/
90% max.
+90˚C
30 min.
glass epoxy board and
—————
—————
—————
Remarks
UL94V-0
UL94V-0
/
/
5 to 35˚C
Within 5 min.